Panasonic Lumix DMC-FP3P Service Manual page 37

Service Manual
Diagrams and Replacement
Parts List
Digital Camera
Model No.
DMC-FP3P DMC-FP3EG
DMC-FP3PC DMC-FP3EP
DMC-FP3PU DMC-FP3GC
DMC-FP3EB DMC-FP3GF
DMC-FP3EE DMC-FP3GH
Vol. 1
Colour
(S)...........Silver Type (only P/PU/GC/GF/GH/GK)
(K)...........Black Type
(N)...........Gold Type (only PU/GF/GH/GK/GN/GT)
(PA).........Light Pink Type (only GF/GH/GK/GN/GT)
(V)...........Violet Type (except P/PC/PU/EP/GN)
(AA).........Blue Type (only GF/GH/GK)
(AB).........Navy Type (only P/PC/EB/EG/GK)
(P)...........Pink Type (only GC/GK)
(G)...........Green Type (only GK)
(D)...........Orange Type (only EG/GK)
(R)...........Red Type (except PC/EE/EP/GT)
(H)...........Gray Type (except P/PC/GC/GF/GH/GT)
Table of contents
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Flash Top P.C.B. .................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Top Schematic Diagram .............................................. S-5
S4.3. Lens Switch Schematic Diagram .......................................... S-5
S5. Print Circuit Board .................................................................... S-6
S5.1. Flash Top P.C.B. .................................................................... S-6
S5.2. Lens Switch P.C.B. ................................................................ S-7
S6. Replacement Parts List ............................................................ S-9
DSC1002015CE
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
COMPONENTS IDENTIFIED WITH THE MARK
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
3.The voltage being indicated on the schematic diagram is measured in
DMC-FP3GK
4.Although the voltage and waveform available on here is measured with standard frame,
DMC-FP3GN
DMC-FP3GT
5.The voltage being indicated here may be include observational-error (deviation) due to
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
S7. Exploded View ....................................................................... S-14
S7.1. Frame and Casing Section.................................................. S-14
S7.2. Packing Parts and Accessories Section (1) ........................ S-15
S7.3. Packing Parts and Accessories Section (2) ........................ S-16
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
when the TP (Test Point) indicated as "
"Standard-Playback" mode when there is no specify mode is mentioned.
it may be differ from actual measurement due to modification of circuit and so on.
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
Circuit name being connected.
OFTR FEP
Name of Signal
S-1
HAVE THE SPECIAL CHARACTERISTICS
" mark.
This signal is connected
to the FEP schematic diagram.