Table of Contents
Advertisement
Connecting Components not Reached by the Remote
Controller Signals (IR IN)
In order to use the remote controller to control the
DTR-10.5 from a remote location, you will need to
prepare a multiroom kit (sold separately) such as one
listed below:
• Multiroom kits such as those made by Niles
®
Xantech
RF Receivers can also be used with the remote controller
to control the DTR-10.5 from a remote location. To use
RF Receivers, set the Transmission Signal Format set-
ting to "RF" (See page 141 for details).
If Remote Controller Signal Does not
Reach the DTR-10.5 Remote Sensor
Effective Sensor Layout
Example for the main room
If the DTR-10.5 is located inside a cabinet or other
enclosure where the infrared rays from the remote
controller cannot enter, then operation with the remote
controller will not be possible. In such a case, it will be
necessary to install a remote sensor at a location outside of
the cabinet so that the infrared rays from the controller can
be sensed.
Connecting
block
IR IN
DTR-10.5
In the
cabinet
Example for the remote zone (Zone 2/Zone 3)
The IR IN input allows you to control the DTR-10.5
from the remote zone (Zone 2/Zone 3) with the remote
controller even though the remote zone may be on the
other side of the building from the main zone. The
diagram below shows how to make the proper
connections for the remote zone.
To IR IN
DTR-10.5
Connecting
block
Main room
48
®
and
IR Receiver
Remote controller
Main room
: Signal flow
IR Receiver
Remote controller
Zone 2/Zone 3 room
: Signal flow
Effective Sensor Connections
When connecting a multiroom kit, use the IR connection
Phoenix (Pluggable connector) terminal (smaller one)
supplied with the DTR-10.5.
Connect the ribbon cable from the connecting block to
the IR connection Phoenix terminal.
1. Loosen the screws using a flatblade screwdriver to
open the shutters.
2. Connect the white wire to the MAIN, ZONE 2 or
ZONE 3 terminal according to the room where the
multiroom kit is used, and then close the shutter.
3. Connect the red wire to the +12V terminal, and then
close the shutter. If you use more than one multiroom
kit in different rooms such as MAIN and ZONE 2,
connect all the red wires to the +12V terminal
together.
4. Connect the black wire to the GND terminal, and then
close the shutter. If you use more than one multiroom
kit in different rooms, connect all the black wires to
the GND terminal together.
Ribbon cable
Red
Black
White
+12V
GND
IN
When the multiroom kits are used for all the rooms
From Main room
Red
White
ZONE 2
Red
White
ZONE 3
Red
White
5. As shown in the illustration below, connect the Phoe-
nix terminal firmly to the IR IN socket on the
DTR-10.5.
A
B
C
DIGITAL IN
D
DIGITAL IN
E
MULTI
F
AUDIO IN
G
H
S VIDEO
VIDEO
I
COMPONENT
J
K
L
OPTICAL
COAXIAL
IN 1
- CH
R
L
R
L
IN
IN
IN 1
VIDEO
12 V
RS 232
FR
FL
IN 2
COMPONENT VIDEO
ANTENNA
HDMI
TRIGGER
(
HD/BNC
)
IN
OUT
1
1
PH
4
1
Y
Y
IN 1
E
SUB
C
2
2
5
2
P
B
GND
R
L
P
SR
SL
B
"Net-Tune"
is a trademark of
3
3
1
6
3
P
R
IR IN
Onkyo Corporation.
FM
SBR
SBL
OUT 1
IN 3
75
+
12 V DC PWR SUPPLY
20mA MAX.
P
R
GND
4
4
2
7
4
Y
IN 2
MAIN
OUT
ZONE 2
FR
FL
ETHERNET
ZONE 3
5
5
3
8
5
P
B
(
Net-Tune
)
Y
AM
SUB
C
6
6
1
9
6
P
R
A
200mA MAX.
SR
SL
P
B
B
100mA MAX.
C
100mA MAX.
1
1
2
4
1
3
GND
SBR
SBL
D
100mA MAX.
P
R
E
TOTAL
2
2
3
5
2
4
100mA MAX.
OUT
R
L
OUT
R
L
OUT
OUT
OUT
S VIDEO
VIDEO
VIDEO
S VIDEO
- CH
MULTI
12 V
IN 2
TRIGGER OUT
SURR R
SURR BACK R
(
ASSIGNABLE
)
FRONT R
CENTER
FRONT L
SURR BACK L
ASSIGNABLE
(
)
SURR L
PRE OUT A
(
SINGLE
)
FRONT
SURR
SURR
AC INLET
BACK
A
SPEAKERS A
L
AC OUTLET
AC 120V
60Hz
R
SWITCHED
120W 1A MAX.
B
SPEAKERS B
CENTER
SUB
SUB
FRONT R (BTL)
FRONT L (BTL)
WOOFER
WOOFER
PRE
UDD
MODEL NO.
DTR-10.5
OUT B
Flatblade
screwdriver
+12V
GND
MAIN
ZONE 2
ZONE 3
Push the connec-
tor into the socket
until it clicks.
Advertisement
Table of Contents
