Related Manuals for Snap Fresh BBT-POL36
Summary of Contents for Snap Fresh BBT-POL36
- Page 1 User Manual CORDLESS SCREWDRIVER BBT-POL36 Please scan the QR CODE for more services. Read all safety rules and instructions carefully before operating this tool. geprufte Sicherheit...
-
Page 2: Table Of Contents
CONTENTS General power tool safety warnings ..................1. Work area safety ................................2. Electrical safety ..............................3. Personal safety ..............................4. Power tool use and care ..........................5. Use and handling of the cordless electrical power tool ........6. Service .................................... -
Page 3: General Power Tool Safety Warnings
General power tool safety warnings WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "powertool"... -
Page 4: Personal Safety
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. -
Page 5: Power Tool Use And Care
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situati- ons. -
Page 6: Use And Handling Of The Cordless Electrical Power Tool
e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. -
Page 7: Service
d) Fluids may leak out of rechargeable battery units if they are misused. If this happens, avoid contact with the fluid. If contact occurs, flush the affected area with water. Seek additional medical help if any of the fluid gets into your eyes. Escaping battery fluid may cause skin irritation or burns. -
Page 8: Safety Guidelines For Screwdrivers
b) Never try to repair damaged batteries. Batteries should only be maintained by the manufacturer or an approved customer service centre. Safety guidelines for screwdrivers WARNING! Hold the power tool by the insulated gripping surfaces when performing an operation where a screw may contact hidden wiring. -
Page 9: Introduction
Introduction Congratulations on the purchase of your new appliance. You have chosen a high-quality product. The operating instructions are part of this product. They contain important information about safety, usage and disposal. Before using the product, please familiarise yourself with all the operating and safety instructions. Use the product only as described and for the range of applications specified. -
Page 10: Assembly
Assembly... -
Page 11: Features
Features LED lamps Torque selection ring Rotation direction switch: right Rotation direction switch: left Battery charge level indicator Charging socket Torque selection display Tool holder Insulated bits Charger Package contents 1 * cordless screwdriver with torque pre-selection 6 * insulated screw bits (SL0.3.5/SL0.8.0/PH1/PH2/PZ1/PZ2) 1 * charging cable 1 * charger... -
Page 12: Technical Specifications
IP 4X, Protection against penetra- tion by foreign bodies φ> 1 mm. Keep away from tools and wires Max. torque 0.4 Nm (electrical operation) 8 Nm (manual operation) Charger BBT-POL36-1 INPUT 100-240v~(AC), 50/60 Hz Rated voltage 0.4 A Rated current... - Page 13 Screws 0.79 m/s Vibration emission value 1.5 m/s Uncertainty NOTE NOTE The vibration emission values and the noise emission values given in these instructions have been measured in accordance with a standardised test procedure and can be used for comparing one power tool with another. The specified total vibration values and the noise emission values can also be used to make a provisional load estimate.
-
Page 14: Before Use
Before use Charging the battery NOTE NOTE The battery is supplied partially charged. Before first use, charge the battery in the charger for approx. 1 hour. This guar- antees full battery power. Li-ion batteries can be charged at any time without adversely affecting their service life. Interrup- tion of the charging process will not damage the battery. -
Page 15: Inserting Bits
Inserting bits WARNING! The insulated bit must be visually checked by the user before each use. The insulation must be checked for possible damage, among other things. If there is any doubt about the safety of the isolated bits, they should either be scrapped or examined by an expert. -
Page 16: Use
Switching the cordless screwdriver on/off Switching on To start the cordless screwdriver, press and hold either the rotation direction switch: right or the rotation direction switch:left The LED lamps light up. Switching off To stop the cordless screwdriver, simply let go of the rotation direction switch: right or the rotation direction switch: left... -
Page 17: Maintenance, Storage And Cleaning
Maintenance, storage and cleaning WARNING! RISK OF ELECTRIC SHOCK! Before cleaning, disconnect the charger from the mains socket. WARNING! The insulated bits should be stored carefully to minimise the risk of damage to the insulation during storage or transport. The insulated bits should generally be stored separately from other tools to avoid mechanical damage or mix-ups. -
Page 18: Disposal
Disposal The packaging is made of environmentally friendly materials which you can dispose of at your local recycling centre. NOTE NOTE The integrated rechargeable battery in this appliance cannot be removed for disposal. The integrated lithium-ion battery may only be removed by trained personnel. -
Page 19: Warranty
Warranty Ningbo Babytec Technology Co., Ltd (Hereinafter referred to as Babytec) warrants this product against defects in materials and/or workmanship under normal use for a period of ONE (1) YEAR from the date of purchase by the original purchaser (’Warranty Period’). The following circumstances are excluded from this guarantee: Repairs and or alterations have been made or attempted to the machine by unauthorized service centers;...
Need help?
Do you have a question about the BBT-POL36 and is the answer not in the manual?
Questions and answers