Advertisement
Quick Links
Advertisement
Related Manuals for Onson J30
Summary of Contents for Onson J30
- Page 2 Please read the instructions before using the product - the warranty card is included and the picture is for reference only...
-
Page 4: Information Security
Information Security... - Page 5 According to the different product model, the product you purchase may not contain all of the above components. Email: customer@onson.shop Telephone: 1-855-919-0908 Address: 1601, Building 2, No. 1, Qingqing Road, Qinghu, Longhua District, Shenzhen, China...
- Page 6 Product Package List and Introduction Robot cleaner (Qty*1） Recharge push button · Short-Press the button to start the recharging function. Clean/switch robot cleaner push button · Short press the button to start the cleaning function. ·Long press to turn on or off. Partial Local sweep button ·Short press to start local cleaning.
- Page 7 Product Package List and Introduction Robot cleaner Laser distance measurement sensor Loudspeaker Infrared recharge sensor/infrared TOF sensor along the wall/ anti-collision sensor infrared auxiliary recharge sensor Collision sensor Laser head plate cover Laser head plate cover laser cover pressure sensor Infrared auxiliary recharge sensor Dust box Dust box button...
- Page 8 Product Package List and Introduction Robot cleaner Charging connected charging pole sheet Universal direction wheel Cliff sensor Side brush Driven wheel Rolling brush Dust collector connection charging pole plate...
- Page 9 Product Package List and Introduction Accessories list Dust box Before using the dust box module, it is necessary to find the accessory - filter screen, and then use after installing the filter screen. Dust box top holder Dust box filter screen Dust box bottom holder...
- Page 10 Product Package List and Introduction Accessories list 1. Recharge dock Recharging dock indicator light Signal emission area Charging spring plate Recharger seat front Recharger seat adapter Power cord length 1.2m Power source interface Recharger seat back...
-
Page 11: Installation
Installation 1. Install a recharging dock Lean the recharging dock against the wall, lay on flat levelled ground. Lean against the wall Not leaning against the wall Make sure the recharging dock is 1.2 meters distance in vertical front direction and 0.5 meters on both sides. - Page 12 Installation Long press to start the robot cleaner, press the return key to automatically find the charging dock for charging. On/off push button indicator light color represents power · white: power load ≥ 15% · orange light breathing: power load < 15% ・Note: If the power is low, it may not be possible to start the robot cleaner.
- Page 13 Installation 3. The App Settings Connect to the mobile phone client terminal (if you do not need to use App control, this step can be skipped). Download the App Scan the QR code below to download and install the App.
- Page 14 Operation instruction Power on/power off Whole House Clean Short press to start the whole room cleaning (see the Long press the button to start the robot cleaner, the key indicator picture below). lights up slowly, and the robot cleaner enters standby mode. When the robot cleaner is at static motionless status,long press to shut Press any key to pause while cleaning.
- Page 15 Operation instruction Partial cleaning Dormancy When the robot cleaner is in standby or paused, short press If there is no operation maintaining exceeding 20 minutes, the the local key sweep key to start the partial location sweep. cleaner will automatically enter the dormancy state. In the This mode is used to clean the square area with the robot dormancy state, after the breathing lamp is off, press any key cleaner as the center of 1.6m x 1.6m.
-
Page 16: Daily Maintenance
Daily maintenance Main brush (weekly cleaning is recommended) Middle sweep rolling brush cleaning tolls use instruction 1. Turn over the cleaner, press down the clasp and remove the main brush cover. 2. Take out the main brush upward and clean the main brush bearing. 3. - Page 17 Daily maintenance Side brush (weekly cleaning is recommended) Use a screwdriver to unscrew and clean the brush. Note: it is recommended to replace the side brush every 3-6 months to ensure the cleaning effect. Battery The robot cleaner is equipped with a high-performance rechargeable lithium battery pack. In order to maintain the battery performance, please keep the robot cleaner under charging condition for daily use.
- Page 18 Daily maintenance Dust box and filter mesh (weekly cleanup is recommended) 1.Push the dust box release button to take it out. 2. Open the dust box clasp. 3. Empty the garbage. 4. Open the dust box clamp-shell and dismantle the filter cover and filter mesh (HEPA).
- Page 19 Daily maintenance Robot cleaner sensor Cliff sensor Wipe and clean each sensor of the robot cleaner with a soft dry cloth, including: Charge connection charging pole plate 1. Four cliff sensors at the bottom of the robot cleaner. 2. Side wall sensor on the right side of the robot cleaner. 3.
- Page 20 Daily maintenance Universal direction wheel Recharging dock (recommended monthly cleaning) (monthly replacement recommended) wheel Wipe the charging spring of recharging dock with a soft 1.Turn the robot cleaner up proper dry cloth. and pull out the universal Wheel direction wheel. shaft 2.Clean hair and dirt from support...
-
Page 21: Common Parameters
Common parameters Robot cleaner proper Recharge dock Item Parameters Item Parameters Outer dimension 98mm Outer dimension 99mm Battery type 5200mAh Rated frequency Product weight ≈3.6kg Input DC24V 1.2A Output DC24V 1.2A Rated voltage 14.4V Rated frequency Trouble shooting When there is an abnormal occurrence in the robot cleaner, there is quick flicker of on/off key indicator orange, please refer to the following table to solve the malfunction. - Page 22 Common parameters Troubleshooting Solutions The robot cleaner may be stuck or trapped. Please clear obstacles around Please check if the main wheel is stuck the robot cleaner. Please put back the dust box and the filter screen, and confirm that the filter The dust box has been taken out screen and the dust box are installed in place.
- Page 23 Common parameters Problem type Solution Battery power is insufficient, please sit on the charging dock to charge before using; Ambient temperature is too low (below 0℃) or too high (above 50℃), please use in the Unable to start environment of 0-40℃. The charging dock is not energized.
Need help?
Do you have a question about the J30 and is the answer not in the manual?
Questions and answers