Subscribe to Our Youtube Channel
Related Manuals for Hidro-Water XENA 10.1
Summary of Contents for Hidro-Water XENA 10.1
- Page 1 RESIDENTIAL REVERSE OSMOSIS USER / INSTALLER’S MANUAL MA-EN-OSMOSIS XENA10.1-RO-0220-22-FLC-21-V01.0...
-
Page 2: Table Of Contents
Please read this manual carefully following the warnings listed below before going ahead 4.2.- Water inlet installation (Figure-8 & Figure-9) ................6 with the installation and use of the XENA 10.1 osmosis system. If you have any doubts, please contact your distributer. -
Page 3: Checking The Contents
• The XENA 10.1 osmosis system needs a mains current of 220 – 240V less than 1 metre away. • Do not repair or take the system apart on your own. If the system is not working correctly, contact your distributor. -
Page 4: Installation
4.- INSTALLATION 4.3.- Drain clamp installation (Figure-7) The system can be installed anywhere in the residence where there is a water input, a drain a. The drain clamp is designed to adjust the drainpipe for water waste, a 220 – 240 V socket within a metre and sufficient space to be located. The most sealing to 1 ½”. -
Page 5: Membrane Installation
c. Unscrew the filter housing checking that the cartridges are centered, so they ad-just d. Insert the membranes in the correct direction as shown in the following figure. They must be fitted following the arrows on the respective membrane housing, introducing the end that properly with the filter adapter and cup. - Page 6 Here is a diagram of how the system should be installed. h. The other end of the ⅜” tube must be connected to the inlet of the XENA 10.1 osmosis system (figure 1), where it is marked “ENTRADA”. To do so, you must unscrew the inlet elbow nut on the osmosis system and insert the ⅜”...
-
Page 7: Osmosis System Start-Up
5.- OSMOSIS SYSTEM START-UP Open the brass ball valve again (figure 9) and turn the faucet (figure 3) on. In doing so, the system will start to produce water. If the water has a black colour don’t worry, this is normal. It’s caused by the residue the carbon activated granular cartridge lets off. -
Page 8: Procedure For Replacing Cartridges And The Membrane
*The life of the filters and membranes will vary depending on the quality of the water supply, g. Apply sufficient Teflon to the threads of the elbow piece that we took off the post filter and the usage and the amount of impurities it has. screw them back on the new filter. -
Page 9: Faults, Probable Causes And Possible Solutions
7.- FAULTS, PROBABLE CAUSES AND POSSIBLE SOLUTIONS SYMPTOM PROBABLE CAUSE SOLUTION Plastic or SYMPTOM PROBABLE CAUSE SOLUTION Worn postfilter. Replace postfilter. synthetic taste Wait until the water supply has No water supply. been restored. Change the filters, membrane, postfilter Unpleasant Contamination. -
Page 10: Monitoring And Maintenance Control
8.- MONITORING AND MAINTENANCE CONTROL DATE: DATE: SERVICE MADE NEXT SERVICE OBSERVATIONS SERVICE MADE NEXT SERVICE OBSERVATIONS Sediments, GAC y CTO antibacterial cart. Sediments, GAC y CTO antibacterial cart. change change Membrane change Membrane change Postfilter change Postfilter change Sanitization Sanitization Reparation Reparation... -
Page 11: Spare Parts
2 1/2” x 2 1/2” Double clamp OI-0234-100 2 1/2” Simple clamp OI-0230-24 Margarita faucet OI-0207-117 XENA 10.1 metal bracket OI-0234-54 XENA 10.1 Pressure gauge OI-0208-24 ⅜” Faucet tube adapter – quick connection OI-0208-13 ⅜” M x ⅜” T Elbow piece... - Page 12 NOTES NOTES MA-EN-OSMOSIS XENA10.1-RO-0220-22-FLC-21-V01.0 MA-EN-OSMOSIS XENA10.1-RO-0220-22-FLC-21-V01.0...
- Page 13 Hidro Water, S.L.U. Carretera Chirivella-Aldaya, 48 Ctra. Aldaya-Chirivella, 48 46960 Aldaya · Valencia, Spain 46960 Aldaya · Valencia, Spain Tel: (+34) 961 98 62 30 Tel: (+34) 961 98 62 30 hidrowater@hidro-water.com hidrowater@hidro-water.com www.hidro-water.com www.hidro-water.com DISTRIBUTOR INSTALLER Sale date Instalation date...
Need help?
Do you have a question about the XENA 10.1 and is the answer not in the manual?
Questions and answers