6.1.- Procedure for replacing cartridges and the membrane ........10 6.2.- Procedure for replacing the WATER STOP anyileak absorbent material 7.- FAULTS, PROBABLE CAUSES AND POSSIBLE SOLUTIONS ..........8.- SPARE PARTS ..........................9.- MONITORING AND MAINTENANCE CONTROL ................................12 9.1.- Ultrafiltration spare parts. ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
2.- PRECAUCIONES Y ADVERTENCIAS Please read this manual carefully following the warnings listed below before going ahead with the installation and use of the ATHENEA ultrafiltration system. If you have any doubts, please contact an official HIDRO-WATER S.L distributer. •...
3.- CHECKING THE CONTENTS Open the packaging and make sure that all of the components are inside, ready for the installation. Figure Description ATHENEA ultrafiltration system main unit New Look Faucet ⅜” PE Tube Feed adapter ¼” M x ¼” T ball valve ⅜”...
Use a drill with a 12mm bit to make a necessary sized hole to put the faucet. c. Fit the tap in the hole as indicated in the fig- ure using a spanner (our reference: OI- 0207-128 not supplied with system) to adjust it tightening the nut. ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
Once you have introduced the ⅜” tube, replace the ⅜” plastic clip. (The pressure reducer has a sticker with an arrow that indicates the way the ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
Page 6
(Our reference: OI-0207-128, not supplied with the system) or a spanner. You must connect the other end of the ⅜” tube to the ultrafiltration system outlet “FAUCET” where it’s marked “FAUCET” (Inlet). To do so, you must insert the ⅜” tube. ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
WATER STOP Antileak system. Keep the other one safe as a spare part. Lower the arm of the system so that water can enter the ultrafiltration system. ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
By not following the maintenance as described in this manual, us- ing original HIDRO-WATER S.L cartridges and by authorized personnel that guarantees the quality of the water produced and the correct operation of the osmosis system, the war- ranty will be void.
Each car-tridge and/or membrane must be placed in the correspond- ing position main-taining the correct order. To do so, you must insert each cartridge in its cap and turn it anti-clockwise. This process must be carried out for each of the car-tridges that you want to replace. ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
Raise the arm on the WATER STOP Antileak system, to cut off the water supply (if there is a leak the arm will already be raised b. Throw away the current absorbent material.esechar el material absorbente que hay colocado. c. Replace it with a new absorbent material ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
Change the filters, membrane, post fil- Contamination. smell ter and sanitise. Wait for the air to pass as there’s no 5. White particles in the Air in the system urgent problem. water Excessive inlet pressure. Check the pressure regulator. ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
⅜” tube faucet adapter OI-0207-64 New Look faucet OI-0207-54 ⅜” plastic insert ⅜” Tube TU-0602-01 ATHENEA Ultrafiltration system support bracket OI-0235-02 QC3 cartridge cups. OI-0208-16 ¼” M x ⅜” T Straight OI-0208-04 ¼” M x ¼” M Double Male connector...
Name and signature of the authorised technician or distribu- tor: DATE: NEXT SERVICE MADE OBSERVATIONS SERVICE Sediments, GAC y CTO cart. change Membrane change Post filter change Sanitization Reparation Name and signature of the authorised technician or distribu- tor: ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
Page 15
Name and signature of the authorised technician or distribu- tor: DATE: NEXT SERVICE MADE OBSERVATIONS SERVICE Sediments, GAC y CTO cart. change Membrane change Post filter change Sanitization Reparation Name and signature of the authorised technician or distribu- tor: ref: MA-UF-0002-EN-V14.0-ATHENEA.pdf...
Need help?
Do you have a question about the ATHENEA and is the answer not in the manual?
Questions and answers