Advertisement
!Maintain correct balance and footing.
!Keep the gun handle dry, clean and free from oil and grease. Clean dry paint or varnish from the nozzle and scrapers after use.
!Allow the gun to cool before storing (only store away when cold). Store the gun in a safe, dry place out of reach of children.
%DO NOT allow children to operate the gun.
%DO NOT direct the hot airflow toward people (including yourself), animals, or plants.
%DO NOT use the gun in a wet environment, or areas of high humidity (i.e. bathrooms, steam rooms, etc.).
%DO NOT use the gun in the rain or on extremely damp days.
%DO NOT obstruct the hot airflow by blocking or covering the air outlet.
%DO NOT touch the hot air nozzle as it becomes extremely hot.
%DO NOT place the heat gun on any surface whilst running, except when using the gun by standing on end in an upright position.
%DO NOT allow the gun to fall over whilst operating free standing in an upright position.
%DO NOT leave the heat gun running unattended. Always turn the power supply OFF and do not leave until the gun has cooled.
%DO NOT force the gun to achieve a task it was not designed to perform.
%DO NOT use the gun in combination with chemical strippers.
%DO NOT operate the gun when you are tired, under the influence of alcohol, drugs or intoxicating medication.
% DANGER! DO NOT USE THE HEAT GUN AS A HAIR DRYER
2.
POWER INFORMATION
2.1. Be sure the power supply you are using agrees with the plate marking on the Heat Gun. The gun is designed to run on 230V/ 50Hz
alternating current. Voltage decreases greater than 10% can cause loss of power and possible overheating.
2.2. The gun is double insulated for added safety .
WARNING: Double insulation does not take the place of normal safety precautions, but acts as a safeguard against injury resulting
from a possible electrical insulation failure inside the gun.
3.
TECHNICAL DATA
MODEL NO. HS100CE
Power:
Temp Range:
Air Volume:
2 Speed
Accessories:
MODEL NO. HS102 (Model HS102K
includes accessory kit)
Power:
Temp Range:
Air Volume:
2 Speed
Accessories:
4.
USE AND INFORMATION
4.1.
Preparing the hot air guns for use.
4.1.1.
Before plugging into the mains ensure the gun is in the OFF position.
4.1.2.
When ready to commence work set power switch to desired temperature setting. Allow one and a half minutes.
4.1.3.
STANDING THE GUN ON END: Both guns may be stood on end in an upright (vertical) position.
4.1.4.
Ensure the surface on which you will stand the gun is flat, level, and free from dirt.
4.1.5.
HS100CE balances on the end of its main body and handle.
4.1.6.
HS102 balances on the end of its main body and the metal arm on the end of the handle. The arm may also be used to hang
the gun up in order to cool.
WARNING!
KEEP HANDS AWAY FROM THE IMMEDIATE NOZZLE AREA. IF LEAD PAINT IS BEING REMOVED FOLLOW THE SAFETY
WARNING AT THE BEGINNING OF THIS MANUAL. ALWAYS WEAR GLOVES AND EYE PROTECTION.
4.2.
Paint and varnish removal.
The easy removal of paint and varnish requires practice. Follow these simple working techniques to achieve the required result.
NOTE: the heat gun is designed to remove both oil and latex based paints and varnishes from surfaces. It will not remove stains
or primer coats that have impregnated the surface of the wood.
4.2.1.
Switch the gun on and allow it to reach its operating temperature.
4.2.2.
Always test on a small unobtrusive area first. If satisfactory, proceed with the task in hand.
4.2.3.
Hold the gun nozzle 3” to 4” from the paint to be removed.
4.2.4.
After a short time paint will soften and begin to blister.
4.2.5.
Do not overheat the paint as this will cause it to burn making it more difficult to remove. Wear eye protection, especially when
stripping paint from overhead. If lead paint is being removed, refer to the warning at the beginning of this manual.
4.2.6.
Begin scraping the paint off. Work from top to bottom. Use a scraper with smooth even strokes, warming the surface in front
of the scraper by moving the gun slightly from side to side.
4.2.7.
If the correct temperature has been applied to the paint, thick even layers can be removed in a single pass (paint should
be removed in strips equal in width to the scraper blade).
4.2.8.
Keep the scraper blade edge clean and sharp preventing paint peelings from building up.
4.2.9.
Scrape paint as soon as it becomes soft, as it will re-harden very quickly.
4.2.10.
After softening, shaped or profiled surfaces may be stripped by using a wire brush.
230V 1500Watts
300°C/525°C
240/450 ltr/min
Optional nozzles
May be handled or
stood vertically on a
non-slip base.
230V 2000Watts
100°C/600°C
300/600 ltr/min
Optional Welding Kit
On/Off &
Fan High
May be handled or
and Low
stood vertically on a
non-slip base.
Stand
Switch
On/Off &
Fan High
and Low
Reference data for above accessories:
Switch
1.
HS100/1 Fish Tail Nozzle
2.
HS100/2 Window Nozzle
3.
HS100/3 Deflector Nozzle
4.
HS100/4 Reduction Nozzle
Temperature
regulator
Reference data for above Welding Kit:
1. HS102K/1 Plastic Welding Rods (ABS)
2. HS102K/2 Plastic Welding Nozzle
3. HS102K/3 9MM Reduction Nozzle
HS100CE, HS102 & HS102K - 1 - 151002
Advertisement
