Table of Contents
Advertisement
USING YOUR OVEN (CONTINUED)
4.
Touch the
button as often as necessary, until the
'end time'
symbol appears flashing.
5.
Set the desired switch-off time using
or
the 'end time'
symbol is flashing.
6.
5 seconds after the last change the 'cook time' and
'end time' arrows are lit to confirm that the oven has
been programmed.
7.
When the delayed start cooking time has elapsed, a
signal will sound and the appliance will turn off. To
stop the signal, press any button on the clock and
then turn the oven function selector to OFF.
NOTE: Delayed start cooking time cannot be set for the
Rapid Heat function.
The feature can be cancelled at any time by returning the
function selector to OFF.
Additional Functionality
Setting the countdown timer
Use this for timing any activity. For example boiling eggs.
1.
Touch the
button, the display will flash.
2.
Set the countdown time you want by using
. Commence with setting the number of seconds
first. The minutes and hours can then be set by
subsequently pressing the
button again and
adjusting using
or
. 5 seconds after the last
change the timer will stop flashing, confirming the
timer has been set.
3.
To cancel the timer touch the
button, the display
will flash. Then touch and hold
and
until the timer is cleared.
4.
To stop the beeper, touch any button.
NOTE: The clock display cannot be selected when the
timer is operating.
Elapsed Time
When an oven function is selected (other than pyrolytic
clean) an elapsed timer commences on the display.
To reset this timer touch and hold both the
buttons until the timer is reset.
Displaying the oven temperature
During operation of the oven the current oven
temperature during pre-heating of the oven can be
displayed by touching the
button. During normal
operation the set temperature can be reviewed by
touching the
button.
NOTE: this temperature will only be displayed for
approximately 5 seconds.
Light operation
During operation of the oven the light can be switched
off by touching and holding the
button until the
16
USING YOUR OVEN
light turns off. Also the light can be turned on from the
standby state by touching and holding the
until the light comes on.
whilst
Activating the child-proof lock
When the child lock is engaged, the oven cannot be
operated and the door cannot be opened.
1.
Switch off the appliance using the function
selector switch.
2.
Touch and hold the
and
buttons at the same
time until the word 'SAFE' is displayed and a double
beep is sounded. The word SAFE will be replaced by
a padlock symbol on the display after 5 seconds.
Releasing the child-proof lock
Touch and hold the
and
buttons at the same
time until a double beep is sounded. This will commence
to unlock the door and after 5 seconds the oven is ready
for use.
Activating the function lock
The active function can be locked so it is not changed
and
unintentionally.
1.
The active function can be locked, to activate touch
and
together until 'Loc' is displayed.
2.
If the oven is switched off while in 'Loc' it will switch
into Child lock mode and the display will show 'SAFE'.
3.
Oven can be released the same way as 'Releasing the
child proof lock'
buttons
Safety Cut-out feature
The oven automatically switches itself off if the
temperature is not adjusted or the appliance is left
operating after a period of time. The oven switches itself
off after:
•
12.5 hours when the temperature is set less than
120°C.
•
8.5 hours when the temperature is set to 120°C
or above, and below 200°C.
and
•
5.5 hours when the temperature is set to 200°C or
above, and below 250°C.
•
3.0 hours when the temperature is set at 250°C.
DEMO Mode
The oven can be set to operate in a demo mode (e.g. in a
retail store). In this mode the display works and functions
can be set but the oven does not actually heat. When
in this mode the text 'DEMO' will be lit. The following
instructions show how to enter and exit 'Demo' mode.
1.
Ensure the oven is in the off state. Toggle and hold
the selector to
until a beep sounds. The 'DEMO'
text will begin to flash.
2.
Toggle the temperature selector to set the first digit
of display to 2. Touch clock to set.
3.
Repeat step 2 until display shows 24:68. 3 beeps
sound and DEMO will be shown.
button
4.
To disable DEMO mode repeat steps 1-3.
Pyrolytic cleaning of the oven cavity
The oven has the Pyrolytic self-cleaning function. It
cleans by burning off the spatters and accumulated dirt
and grease from the oven liner, at high temperature. This
process produces ash which can then be wiped out of the
oven cavity.
Pyrolytic cleaning will not remove salt and mineral
residue left in the cavity well when water evaporates.
It is recommended that the residue is cleaned prior
to conducting pyrolytic cleaning cycles. See section
'Cleaning the cavity well'.
WARNING
During the pyrolytic cleaning process the oven becomes
extremely hot.
•
Please keep small children at a safe distance.
•
Never clean non-stick baking trays and tins in the
oven during the pyrolytic cycle. High temperatures
damage the non-stick coating and poisonous gas
is released.
•
To prevent damage, do not use acids, sprays or
similar cleaning agents.
CAUTION
•
During pyrolytic cleaning the air outlet exhaust
above the door must be kept clear of any
obstruction (e.g. bulky tea towels).
•
Do not use the oven to clean miscellaneous items
(e.g. cookware).
Before carrying out the Pyrolytic function
1.
All accessories must be removed from the oven,
including shelves, trays and side racks.
2.
Clean large deposits, spills or grease from the
oven cavity.
3.
Ensure the cavity well is free of limestone scaling
(refer to cleaning the cavity well chapter)
4.
Choose the Pyrolytic cleaning cycle from
the following:
soiling
light clean
normal clean
NOTE: Duration includes heat-up time, excluding
cool-down time.
Light clean
This is an energy saving cycle that can be used on a
regular basis if the oven is lightly soiled. Possibly after
every 2nd or 3rd roast.
Normal clean
Use this as the regular cycle about once every
2-3 months.
Pyrolytic Cleaning Operation
The pyrolytic cleaning function can be selected by turning
the function selector switch clockwise to the pyrolytic
position. Use
or
cleaning time of 1:30 hours or 2:30 hours. The pyrolytic
function can be stopped at any time by turning the
function selector counterclockwise to the OFF position.
IMPORTANT
During Pyrolytic cleaning the door will automatically
lock when the temperature in the oven approaches
300˚C.
will appear on the display. During the
pyrolytic cleaning cycle there may be some burn off
odours. It is advised to keep the room well ventilated
during this cycle.
When the pyrolytic cleaning function is on, it is advisable
not to use a cooktop if it is fitted above the oven. This
could cause overheating and damage to both appliances.
The door will only unlock when the oven has cooled to a
safe temperature. Turning the function off will not unlock
the door. This will only happen when safe temperature
is reached.
NOTE: The cooling fan will operate at an increased speed
for Pyrolytic cleaning and will continue to run until the
oven has cooled down. This is normal. It is recommended
to clean the oven regularly to keep it in its best condition.
duration
1hr 30mins
After Pyrolytic cleaning
2hr 30mins
After cool-down, wipe the ash out of the oven with a soft
damp cloth and warm water.
To restore the enamel shine to more difficult areas, use a
damp cloth with vinegar and detergent.
CAUTION
Do not turn off the mains power supply to the
oven during the pyrolytic cycle. This could
damage the appliance.
to toggle between a pyrolytic
This knob cannot be
turned anticlockwise
from off position
17
USING YOUR OVEN
Advertisement
Table of Contents
