Haier 1407 Service Manual
Hide thumbs
Also See for 1407:
- Owner's manual (28 pages) ,
- Owner's manual (26 pages) ,
- Service manual (16 pages)
Related Manuals for Haier 1407
Summary of Contents for Haier 1407
- Page 1 All manuals and user guides at all-guides.com CAUTION READ THIS MANUAL CAREFULLY TO DIAGNOSE TROUBLE CORRECTLY BEFORE OFFERING SERVICE . SERVICE MANUAL Colour Television Haier model:1407 Customer model: HTAR14...
-
Page 2: Table Of Contents
All manuals and user guides at all-guides.com CONTENTS Safety precautions……………………………………………………………..……………3 TV block diagram……………………………………………………………………..…….4 Replacement of memory IC………………………………………………………….……5 Service adjustment……………………………………………………………..…………...5 ICs functional description…………………………………………………………………8 Test point waveform………………………………………………………………………10 All ICs voltages……………………………..……………………………………………….10 Purity / convergence adjustment………………………………………………………12 CIRCUIT DIAGRAM…………………………………………………………………Attached 10. WIRING CONNECTION DIAGRAM………………………………………………Attached... -
Page 3: Safety Precautions
All manuals and user guides at all-guides.com 1. SAFETY PRECAUTIONS The design of this product contains special hardware, many Isolation Check circuits and components especially for safety purposes. For (Safety for Electrical Shock Hazard) continued protection, no changes should be made to the After re-assembling the product, always perform an isolation original design unless authorized in writing by the check on the exposed metal parts of the cabinet (antenna... -
Page 4: Tv Block Diagram
All manuals and user guides at all-guides.com Block diagram TDA11115HPS/N2 series with mono intercarrier sound demodulator... -
Page 5: Replacement Of Memory Ic
All manuals and user guides at all-guides.com 3. REPLACEMENT OF MEMORY IC 1. MEMORY IC. This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and deflection circuits. 2. PROCEDURE FOR REPLACING MEMORY IC (1) Power off Switch the power off and unplug the power cord from AC outlet. - Page 6 All manuals and user guides at all-guides.com Direct access key Items Description Preset Remark “1” 6HSH/5HSH Horizontal shift 0~63 VG2 Brightness “2” 5/6VSL Vertical slop 5/6VAM Vertical amplitude 5/6SCL S-correction 5/6VSH Vertical shift 5/6VOF OSD Vertical offset HOF* OSD Horizontal offset “3”...
- Page 7 All manuals and user guides at all-guides.com Function Description Preset Remark Bit 7 RUSSIA 1=Enable Bit 6 ITALY 1=Enable Bit 5 GERMANY 1=Enable Bit 4 FRANCE 1=Enable Bit 3 RUTKISH 1=Enable Bit 2 ARABIC 1=Enable Bit 1 FARSI 1=Enable Bit 0 ENGLISH 1=Enable 4.
-
Page 8: Ics Functional Description
All manuals and user guides at all-guides.com 7. OP7 Function Description Preset Remark 1=Enable 1=Enable BLUESCREEN FADE 1=Enable 1=Enable SVHS 1=Enable 1=Enable 8. OP8 Function Description Preset Remark INIT 1=Enable LOGOYEND 1=Enable Note：Don’t adjust any OPTION items, please inform the engineer about any change. 5. - Page 9 All manuals and user guides at all-guides.com VDRA Vertical drive A output IFIN1 IF input 1 IFIN2 IF input 2 IREF Reference current input Vertical sawtooth capacitor TUNER AGC Tuner AGC output AUDEEM/SIFIN1 *1 Audio deemphasize or SIF input DECSDEM/SIFIN2 Decoupling sound demodulator GND2 Ground 2 for TV processor...
-
Page 10: Test Point Waveform
All manuals and user guides at all-guides.com GND(out 1) Ch 1Ground Volume Control Out 1 (-) Ch 1 output (-) Out 2 (-) Ch 2 output (-) Standby Mute input GND(out 2) Ch 2 Ground In 1 Ch 1 input Out 2 (+) Ch 2 output (+) 4. - Page 11 All manuals and user guides at all-guides.com 7. IC voltages TDA11115H 0.18 0.17 TDA4864 TDA1517 2.75 0.35 24C08/PCF8598...
-
Page 12: Purity / Convergence Adjustment
All manuals and user guides at all-guides.com 8. PURITY / CONVERGENCE ADJUSTMENT PURITY ADJUSTMENT WEDGE Demagnetize CRT with the demagnetizer. DEFLECTION YOKE Loosen the retainer screw of the deflection yoke. Remove the wedges. Input a green raster signal from the signal generator, and turn the screen to green raster. - Page 13 All manuals and user guides at all-guides.com STATIC CONVERGENCE ADJUSTMENT 1. Input a crosshatch signal. 2. Using 4-pole convergence magnets overlap the red and blue lines in the center of the screen (Fig. 1) and turn them to magenta (red/blue). (FRONT VIEW) 3.
- Page 14 All manuals and user guides at all-guides.com X105 V0.31 Video CP101 PROG+ PROG- VOL+ VOL- Menu AV/TV D101 SW107 SW106 SW105 SW104 SW103 SW102 +5Vstb R108 R107 R106 R105 R102 1.8K 1.2K R101 C101 3.3K 10uF/16V +3.3Vstb R705 R712 S101 S105 IR-KEY Front AV...
- Page 15 All manuals and user guides at all-guides.com POWER AV PCB BAND Cord Specification Location...
- Page 16 All manuals and user guides at all-guides.com Sincere Forever...