Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SOGEDIS T0 Series
Summary of Contents for SOGEDIS T0 Series
- Page 1 Série T0 CODES PANNES AUTOTEST...
-
Page 2: Lcd Screen, Function Buttons & Knobs
Operating Instructions 3.1. LCD Screen, Function Buttons & Knobs Program Selector with ON/OFF Start / Pause Option Selection Spin Speed Selection Temperature Selection Start / Pause Led Option Led 7-segment display 1 7-segment display 2 3.2. Program List KNOB PROGRAM POSITION Cotton 60°C Cotton 40°C... -
Page 3: Child Lock
Child lock during selection: 3.3. Child Lock Machine does not respond to any pressing of buttons or changing position of program knob. CL at 7 segment display will Activation make fast blink for 2 sec to indicate child lock is activated. Press the SW2 and SW3 buttons simultaneously for 3 sec. -
Page 4: Test Mode
Test Mode Step6: The option 1 button is pushed 4.1. Autotest The EV1 and EV2 are activated concurrently until it reaches pressure sensor's first level frequency ( Hz ) for 5 seconds. * This test is for quick checking of the product. You can not see the failure codes. - Page 5 Flow chart of the autotest: During test “AU” is visualized on display, at the end of the test “--” is visualized and door is unlocked. During test, pressing other buttons makes no change on display.
-
Page 6: Service Mode
Service Mode 5.1. Service Autotest End users can only see E1-E2-E3-E4. During service autotest, other failures can be seen. To activate service autotest, Press SW3 button and simultaneously position program knob to 1. After 3 sec, door will be locked, and machine enters service autotest mode. Release SW3 button. In T0 "SA"... -
Page 7: Failure Codes
5.2. Failure Codes Indication For User Indication For Service Error Indication Error Number Yes/No Yes/No Door is not locked Door is unlocked during programme Lack of water Pump failure Overflow NTC or Heater Failure Motor Failure - 1 (Tachometer open-short circuit or motor connector is disconnected) Configuration Failure Motor Triac Failure... - Page 8 Water tap is closed. Open water tap. The water inlet hose may be bent. Check the water inlet hose. The water inlet hose is obstructed. Clean the filters of water inlet hose. Machine does not receive water. The water inlet filter is obstructed. Clean the valve inlet filters.
-
Page 9: Component Specifications
Component Specifications 8.1. Drain Pump Drain pump is both a mechanical and elektrical component which is used to drain water inside the washing machine. It has an synchronous motor inside. For better performance maintanance, pump filter should be cleaned regularly. 8.1.1. - Page 10 8.2. Resistance Heating element (Resistance) is a component which is desingned to regulate temperature of water inside the drum. It has three connections: Phase, notral and ground connections. 8.2.1. Technical Features Tubular heating element with NTC – sensor Kind of heating Nominal voltage 230 V 2000 W (±5%)
- Page 11 8.3. Component which sends signals to PCB about the water temperature inside the tub. The Resistance (Ohm) value of the NTC decreases as the temperature increases. 8.3.1. Technical Features Tem (°C) R min (kΩ) R max (kΩ) 54,9 62,6 43,0 48,6 33,9 38,1...
- Page 12 8.4. Valve Valve is an electrical and mechanical component which is designed to take water from the network system into the washine machine. It is operated by PCB card. 8.4.1. Technical Features 220 – 240 V Nominal voltage Nominal power 8 VA Frequency 50-60 Hz...
-
Page 13: Electronic Pressure Switch (Eps)
8.5. Electronic Pressure Switch (EPS) 8.5.1. Technical Features Electromagnetic field occurs as a result of the vibration of the membrane which is under pressure in the coil. The nucleus part is moved up and down by the electromagnetic field. The water level is regulated by the frequency which is controlled by the PCB and changes according to the movement of the nucleus part. - Page 14 8.6. Motor The washing machine has an asynchronous motor. t is controlled by the PCB. It is essential to check the motor for correct diagnosis and quick servicing. In the below picture, socket points on the motor is shown to measure with multimeter.
- Page 15 Tacho and stator (full field-half field) ohm resistance values for the motor types are listed in the below table. STATOR AUXILIARY WINDING TAKO MOTOR CODE SUPPLIER Resistance Resistance Resistance 32016268 WELLING 2,00 ± %7 Ω 66,6± %7 Ω 32030654 G&J 1,86-2,14 Ω...
- Page 16 8.7. Door Lock Door lock is activated at the beginning of the program in order to prevent the door from opening. It can be unlocked approximately after 2 minutes of the program end. This time delay is caused by the PTC which is assambled in the door lock. 8.7.1.
Need help?
Do you have a question about the T0 Series and is the answer not in the manual?
Questions and answers