Layout And Items Supplied - EINHELL TC-SM 2531/2 U Original Operating Instructions

•
Never cut workpieces which are too small to
clamp securely on the saw table.
•
Avoid placing your hands in hazardous posi-
tions in which one or both hands could touch
the saw blade if they slip suddenly.
•
There must be no nails or other foreign bo-
n dies in the workpiece.
•
Always stand to the side of the saw blade
when working with the saw.
•
Never load the machine so much that it cuts
out.
•
Always clamp the workpiece securely on the
saw table with a workpiece clamping device
in order to prevent the workpiece wobbling or
twisting.
•
Ensure that the off-cuts can be removed to
the side of the saw blade. Otherwise it is pos-
sible that they will be caught by the saw blade
and be catapulted out of the machine.
•
Never saw more than one workpiece at once.
•
Never remove loose splinters, chips or
jammed pieces of wood when the saw blade
is running.
•
To rectify faults or remove jammed pieces of
wood, always switch off the machine first. Pull
out the power plug!
•
Carry out retooling work, adjustments, mea-
surements and cleaning jobs only when the
motor is switched off. Pull out the power plug!
•
Switch off the motor and pull the power plug
before you leave the workplace.
•
Damaged or faulty safety devices have to be
replaced immediately.
•
Damaged safety devices and parts must be
repaired or replaced by an authorized service
center.
•
Have damaged switches replaced a
authorized service center.
•
This tool complies with the pertinent safety
regulations. Only authorized service center
electrician using original replacement parts
is are allowed to carry out repairs. Failure to
observe this point may result in accidents for
the user.
•
Refit all guards and safety devices immedia-
tely after you have completed any repairs or
maintenance work.
•
Be sure to observe the safety information
and operating and maintenance instructions
issued by the manufacturer, as well as the
dimensions listed in the Technical Data.
•
It is imperative to observe the accident pre-
vention regulations in force in your area as
well as all other generally recognized rules of
safety.
Anl_TC_SM_2531_2_U_SPK8.indb 41 Anl_TC_SM_2531_2_U_SPK8.indb 41
GB
•
Operation in enclosed areas is permitted
only with a suitable vacuum extraction sys-
tem.
•
Do not use any low-powered machines for
heavy duty work.
•
Do not use the cable for purposes for which it
is not designed!
•
Check that the moving parts are in good wor-
king order, that they do not jam, and that no
parts are damaged. Make sure that all parts
are fitted correctly and that all other operating
conditions are properly fulfilled.
•
Caution: Take extra care when making double
miter cuts!
Please keep these safety instructions in a
safe place

2. Layout and items supplied

2.1 Layout (Fig. 1-5)
1. Handle
2. ON/OFF switch
3. Release lever
4. Machine head
5. Saw shaft lock
6. Adjustable blade guard
7. Saw blade
8. Clamping device
9. Battery for Laser (not supplied)
10. Workpiece support
11. Fixed stop rail
12. Table insert
13. Hexagon key
14. Locking screw
15. Pointer
16. Scale
17. Turntable
18. Fixed saw table
19. Scale
20. Pointer
21. Locking screw
22. Sawdust bag
23. Drag guide
24. Locking screw for drag guide
25. Fastening bolt
26. Table width extension
27. Knurled screw for cutting depth limiter
28. Stop for cutting depth limiter
29. Adjusting screw
30. Adjusting screw
31. Flange bolt
32. Outer flange
- 41 -
30.06.2021 08:18:59 30.06.2021 08:18:59