Subscribe to Our Youtube Channel
Related Manuals for ARRI AMIRA SUP 6.1.2
Summary of Contents for ARRI AMIRA SUP 6.1.2
- Page 1 AMIRA SUP 6.1.2 Software Update Package SUP 6.1.2:83 R E L E A S E N O T E S Date: February 1, 2022...
-
Page 2: Table Of Contents
Table of Contents A. Introduction ........................3 AMIRA SUP 6.1.2 Features and Changes Overview ..............3 Updating..........................3 Downgrading ........................... 3 Software Compatibility Notes ....................3 Registration ..........................3 B. Legal ..........................4 Important Notes on Audience and Intended Use..............4 Important Notes on Vital Precautions .................. -
Page 3: Introduction
It is not possible to downgrade AMIRA cameras to previous SUP versions from this version, if the image sensor of the camera is calibrated at a temperature of 35°C. This may be the case for cameras built by ARRI manufacturing or for cameras that were calibrated in ARRI Service after the release of this software. -
Page 4: Legal
The product is solely and exclusively available for commercial customers and shall be used by skilled personnel only. Every user should be trained according to ARRI guidelines. Use the product only for the purpose described in this document. Always follow the valid instructions and system requirements for all equipment involved. -
Page 5: New Features And Changes In Sup 6.1.2
Several bug fixes have been included. • Support for modified sensor temperature calibration has been included. ARRI manufacturing and ARRI Service can calibrate sensor at a temperature of 35°C instead of 40°C using SUP 6.1.2. Installing SUP 6.1.2 does not change any calibration parameters of your camera. -
Page 6: Known Issues
Accessories • Record Start/Stop on Canon HJ18 B4 lens In case the start/stop function on the Canon HJ18 B4 lens is not working with the ARRI B4 Mount and connected Hirose cable, please execute a "Reset all" on the lens. - Page 7 • HD-SDI output performance with DL 6G For best DL 422 6G SDI output performance we recommend upgrading to the new SDI board IOAX Rev.H. For any inquiries please contact your local ARRI service center. • No Return-In in MPEG-2 mode with psf or interlaced signals The Return-In input is not supported when the camera is in MPEG-2 mode and the return signals are psf or interlaced.
- Page 8 No action is required if no warning is displayed. Please contact ARRI service for more information or if you encounter any further issues. • Indicated available recording time with MPEG 2 In MPEG 2 recording mode, the available recording time displayed by the camera may be shorter than the actual available recording time.
- Page 9 LBUS devices (Master Grips, CForce motors, LCUBE) cannot be updated on the AMIRA using cable EXT - LBUS. Please use an ALEXA Mini, an UMC-4 or a WCU-4 with cable LCS - LBUS, or contact your local ARRI Service. Usability •...
- Page 10 For AMIRA cameras equipped with the modified SDI board "IAOX-M" (like the AMIRA CL), the Genlock Sync menu does not show the ref in/analog option at the first boot up after installation of SUP 6.1. With any further boot, the option will be displayed. AMIRA SUP 6.1.2 Page 10 of 12 Release Notes...
- Page 11 For a stable genlock sync, the return input signal must be a clean signal without distortions. • RCP values may not be consistent The parameter values on the RCP are not mirrored in the positive and the negative range, eg. max values: -87/+89. AMIRA SUP 6.1.2 Page 11 of 12 Release Notes...
-
Page 12: Update Procedure
▪ Connect the USB stick to your computer and place the downloaded *.SUP file in the folder ARRI/AMIRA/SUP on the USB stick. Then place the downloaded *.lic file in the folder ARRI/AMIRA/LICENSES on the USB stick. ▪ SUPs contain not only updates for the camera body. Therefore, the MVF-1 viewfinder, CCP-1 and the lens mount should be attached to the camera when performing an update.
Need help?
Do you have a question about the AMIRA SUP 6.1.2 and is the answer not in the manual?
Questions and answers