Advertisement
Available languages
Available languages
1. CODE.START
(Manage transmitter code start)
The control unit can learn up to 200 transmitters with fixed or rolling codes.
Same function with control unit [10-11] START command input .
Learn codes:
Press [SEL] key brief until [CODE.START] LED flash , press and hold the
transmitter correspond button you want to learn , when [CODE.START]
LED stop flash and light on , learn procedure finish . When all function
LEDS flash , it means memory is full and can't learn more transmitter.
Erase all codes:
Press [SEL] KEY brief until [CODE.START] LED flash, press and hold
[SET] key until [CODE.START] LED light off , all codes in memory will
erased , erase procedure will finish .
2.
CODE.PEDE
(Manage transmitter code pedestrian)
The control unit can learn up to 200 transmitters with fixed or rolling codes.
When pedestrian mode on , the gate will open for 10 seconds , then pause
for 10 seconds and gate will close again.
Setting function same with [CODE.START] .
3.
P-P/DIS-OP
(Command disable during opening and pause)
The command disable during opening and pause function suitable used for
automatic closure with loop detect. During opening and pause , control unit
ignore the command given by loop detect .
Press [SEL] key brief until [P-P/DIS-OP] LED flash , press [SET] key brief.
[P-P/DIS-OP] LED light on , command disable during opening and pause.
[P-P/DIS-OP] LED light off , command mode is step-by-step.
External Menu 1 LED indicated:
T.PAUSE
[T.PAUSE] and [T.MOTOR]
LEDS flash alternately
T.MOTOR
Electronics brake off
LAMP/CORT
P-P/DIS-OP
Pressure maintenance off
CODE.PEDE
Step-by-Step
CODE.START
Remote PGM off
1. CODE.START
(Transmitter learn via radio control)
The control unit allow to enter learn transmitter function via radio control .
Press and hold the transmitter correspond button that already learn over 10
seconds , the standby menu [CODE.START] LED flash , now can learn new
transmitter .
Press [SEL] key brief until [CODE.START] LED flash , press [SET] key brief.
[CODE.START] LED light on , allow transmitter learn via radio control .
[CODE.START] LED light off , disable transmitter learn via radio control .
LED OFF
LED ON
[T.PAUSE] and [T.MOTOR]
LEDS flash alternately
Electronics brake on
Pressure maintenance on
Input invert
Remote PGM on
Agiou Dimitriou 263, TK. 17342, Athens, Greece
4. LAMP.CORT
(Flash lamp or Courtesy light select)
Courtesy light output mode :
When every opening command is given ,
230V lamp will activate for 3 minutes then off.
Flash lamp output mode :
230V lamp will activate when motor is running
or pause time , else 230V lamp is off.
Press [SEL] key brief until [LAMP.CORT] LED flash , press [SET] key brief.
[LAMP.CORT] LED light on , 230V lamp output mode is courtesy light.
[LAMP.CORT] LED light off , 230V lamp output mode is flash lamp.
5.
T.MOTOR
(Motor self-learning , max timer 4 minutes)
The control unit default motor operation time is 30 seconds , without
slow-down function.
Press [SEL] key brief until [T.MOTOR] LED flash , press [SET] key brief
, motor will run opening ; when the slow-down initial point is reached ,
press [SET] key brief again , motor will run in slow-down ;when total
opening point is reached , press [SET] key brief , motor will stop and
opening self-learning is complete , [T.MOTOR] LED start flash rapidly.
Repeat self-learning procedure for motor closing cycle , total motor
self-learning procedure will finish.
To cancel slow-down function of self-learning , when motor running at
the desired point of opening or closing , press [SET] key twice brief in
2 seconds , instead of press once .
6.
T.PAUSE
(Automatic closure pause time , max 4 minutes)
The control unit default without automatic closure function .
Press [SEL] key brief until [T.PAUSE] LED flash , press [SET] key brief and
wait for the desired pause time , then press [SET] key brief again , the
automatic closure pause time is stored and [T.PAUSE] LED will light on.
To cancel automatic closure pause time , press [SEL] key brief until
[T.PAUSE] LED flash , press [SET] key twice brief in 2 seconds , [T.PAUSE]
LED light off and operation finish .
Enter External Menu 1 :
When control unit current in standby menu , press and hold [SET]
key over 5 seconds , the [T.PAUSE] and [T.MOTOR] LEDS flash
alternately , now enter External Menu 1.
Exit to Standby Menu :
When enter External Menu 1 , over 30 seconds without [SEL] or
[SET] key press , control unit will return back to standby menu .
2.
CODE.PEDE
(Step-by-Step or Input invert select)
Input invert means when motor opening , press transmitter button or low
voltage push button brief , motor reverse to run closing immediately .
Same when run closing , immediately reverse to run opening .
Press [SEL] key brief unitl [CODE.PEDE] LED flash, press [SET] key brief
[CODE.PEDE] LED light on , input mode is invert input .
[CODE.PEDE] LED light off , input mode is Step-by-Step .
www.seco.gr
Tel. 0030 210 9846222
Fax 0030 210 9822276
3
Advertisement
