Advertisement
Quick Links
Malibu - 3 Drawer 2+2 Door Robe
Assembly Instructions -
Dimensions
Width - 145.5cm
Depth - 50cm
Height - 181cm
Important -
Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Please keep for future reference
258/6890
268/4534
257/7517
268/2811
244/7142
MADE IN
BRITAIN
Issue 5 - 21/05/14
Advertisement
Related Manuals for Malibu Boats 258/6890
Summary of Contents for Malibu Boats 258/6890
- Page 1 Malibu - 3 Drawer 2+2 Door Robe Assembly Instructions - 258/6890 Please keep for future reference 268/4534 257/7517 268/2811 244/7142 Dimensions Width - 145.5cm Depth - 50cm MADE IN Height - 181cm BRITAIN Important - Please read these instructions fully before starting assembly...
-
Page 2: Care And Maintenance
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs • Make sure you have enough • We do not approximately 101kgs. space to layout the parts before recommend the Please lift with care. starting. - Page 3 If you have damaged or missing components, call the Components - Panels Customer Helpline: 08456 400800 quoting the reference numbers below Please check you have all the panels listed below Left End Right End Left Divider Right Divider (D2852A) (D2853A) (D2854A) (D2855A) (1808 x 496mm)
- Page 4 If you have damaged or missing components, call the Components - Fittings Customer Helpline: 08456 400800 quoting the reference numbers below Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
- Page 5 If you have damaged or missing components, call the Assembly Instructions Customer Helpline: 08456 400800 quoting the reference numbers below Step 1 Prepare the 3 drawer fronts Screw 2 metal dowels into each of the drawer fronts Note: Tighten the metal dowels up fully against the panels.
- Page 6 Assembly Instructions Step 4 Fit the drawer base Slide the drawer base down the grooves in the drawer sides and down into the groove in the drawer front Step 5 Fit the drawer back Fit the drawer back between the drawer sides Make sure that the drawer base...
- Page 7 Assembly Instructions Step 8 Prepare the left divider Finished Place 3 runners front edge the left divider shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw Slide the runner back the other way and fit the 2nd screw into...
- Page 8 Assembly Instructions Step 9 Prepare the right divider Place 3 runners the right divider shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw Finished front edge Slide the runner back the other way and fit the 2nd screw into...
- Page 9 Assembly Instructions Step 10 Prepare the 2 horizontals Tap 2 wooden dowels into each horizontal Step 11 Fit the horizontals to the left divider Push the 2 horizontals Finished onto the left divider front edge and secure with 4 screws Finished Finished front edge...
- Page 10 Assembly Instructions Step 13 Prepare the top, base and 2 rails Tap 2 wooden dowels into the top Finished front edge Tap 2 wooden dowels into the base Tap 2 wooden dowels into each rail Finished front edge Plain chipboard surface Finished front edge...
- Page 11 Assembly Instructions Step 15 Prepare the left end Push a rail holder into the left end . Make sure that it is fitted straight, in line with the Finished panel edges and then front edge secure with screw Fit 3 hinge plates onto the left end , making...
- Page 12 Assembly Instructions Step 17 Fit the right end Push the right end onto the top , base and rail and secure with 5 screws Step 18 Prepare the 2 plinths Tap 2 wooden dowels into each of the 2 plinths...
- Page 13 Assembly Instructions Step 19 Fit the 2 plinths 2 people are needed here Push the plinths onto the right end secure with 2 screws Note: Support this plinth until the left side has been fitted in the next step. Step 20 Fit the left end Push the left end onto the top...
- Page 14 Assembly Instructions Step 21 The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y Fit the back panels Note: Do not nail where the Square up the unit by backs meet.
- Page 15 Assembly Instructions Step 23 Fit the 4 plastic nails Tap 2 plastic nails into the bottom edge of each end shown. Tap 1 plastic nail into each plinth as shown. Stand the unit up for the next step. Warning: The robe is heavy.
- Page 16 Assembly Instructions Step 24 Fit the hanging rails and drawers Push the long hanging rail and 2 short hanging rails into the rail holders Starting with the bottom drawer, slide both the runners forward and locate the drawer sides between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the...
- Page 17 Assembly Instructions Step 26 Fit the loose shelves Lower the 2 loose shelves down onto the shelf studs Step 27 Prepare the 4 doors Push fit 3 hinges into each large door 2 hinges into each short door Secure each hinge with 2 screws Note: Before securing with the screws, make...
- Page 18 Assembly Instructions Step 28 IMPORTANT Drill a handle hole in Carefully choose which hole you each short door need to drill in each short door Important: Please follow these instructions carefully. ONLY drill this hole in 1 short door Lay the 2 short doors down onto a smooth surface.
- Page 19 Assembly Instructions Step 29 Fit doors and handles Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges. Push the hinge onto the front part of the hinge plate The recess at the bottom of screw B goes into the slot in the hinge plate.
- Page 20 Assembly Instructions Step 30 Adjust the doors if needed Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges,...
- Page 21 Assembly Instructions Step 31 Attach bracket to top To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit. Fixings are not supplied, as they will need to suit Top of Unit the wall type and the length of screw will...
- Page 24 ALR3034...