PHD GRF Series Installation

SERIES GRF GRIPPERS SWITCH KITS & INSTALLATION
SOLID STATE & REED SWITCH MOUNTING REQUIRES -CU OPTION GRF SIZE 25, 28, & 32
INSTALLING TARGET ASSEMBLY.
1) Apply removable threadlocker to target mounting
set screw, loosely install in target assembly.
2) Place target assembly on -CU target pin with
magnet orientation marker aligned as shown.
3) Tighten target mounting set screw to the
recommended torque specification. (Table 1)
SERIES 6790
SERIES 6790 SWITCH
ORIENT AS SHOWN IN
BRACKET (SWITCH NOT INCLUDED)
SWITCH
MOUNTING
SCREW
SWITCH BRACKET
TARGET MOUNTING
SET SCREW
CU
MAGNET ORIENTATION
TARGET PIN
MARKER
MAGNETIC
TARGET ASSEMBLY
6790 & JC1SDx
SWITCH MOUNTING KITS
GRIPPER SWITCH MOUNTING KIT
SIZE REED
25 76113-25
28 76113-28
32 76113-32
KIT INCLUDES: 2 Brackets for Switches
1 Magnetic Target Assembly
1 Set Screw for Target Mounting
2 Set Screws for Brackets
SENSOR
TYPE
ALL
PROXIMITY
SWITCH
SOLID STATE
& REED SWITCH
INSTALLING & ADJUSTING 6790 SWITCHES.
1) Insert switch into switch bracket as shown.
2) Slide switch and bracket assembly into slots
in body.
3) Adjust on/off position of switch and bracket
assembly per your requirements.
4) Tighten switch screw to recommended torque
specification. (Table 1)
SERIES JC1SDx
SWITCH
MOUNTING
SCREW
SWITCH BRACKET
SWITCH BRACKET
MOUNTING SCREWS
TARGET MOUNTING
SET SCREW
MAGNET ORIENTATION
SOLID STATE
76112-25
76112-28
76112-32
Table 1 - GRIPPER ASSEMBLY TORQUES
DO NOT EXCEED RECOMMENDED TORQUE SPECIFICATIONS
PART DESCRIPTION
TARGET MOUNTING SET SCREW
4 mm ROUND PROXIMITY SWITCH CLAMPING SHCS
PROXIMITY SWITCH BRACKET MOUNTING SET SCREW
SHCS FOR 6 mm SQUARE SWITCH BRACKET
6790 & JC1 SWITCH MOUNTING BRACKET SET SCREW
JC1 SWITCH MOUNTING SCREW
6790 SWITCH MOUNTING SCREW
SERIES JC1SDx SWITCHES
ORIENT AS SHOWN IN
BRACKET (SWITCH NOT INCLUDED)
CU
MARKER
TARGET PIN
MAGNETIC
TARGET ASSEMBLY
JC1 SWITCH DETAIL VIEW
BACK OF SWITCH
SWITCH
BRACKET
FRONT OF SWITCH
(PHD LOGO, LED,
HEX SET SCREW)
SWITCH BRACKET
MOUNTING SCREW
HEX WRENCH
(SUPPLIED WITH SWITCH)
9 in-lb
For additional technical assistance, call or visit our web site:
INSTALLING & ADJUSTING JC1 SWITCHES.
1) Insert switch into switch bracket as shown.
Align switch screw with hole on the side of
the bracket and tighten to recommended
specification. (Table 1)
2) Slide switch and bracket assembly into slots
in body.
3) Adjust on/off position of switch and bracket
assembly per your requirements.
4) Tighten bracket set screw to recommended
torque specification. (Table 1)
SERIES JC1STx
SERIES JC1STx SWITCH
ORIENT AS SHOWN IN
BRACKET (SWITCH NOT INCLUDED)
SWITCH BRACKET
SWITCH BRACKET
MOUNTING SCREW
TARGET MOUNTING
SET SCREW
MAGNET ORIENTATION
MARKER
JC1STx SWITCH MOUNTING KITS
GRIPPER
SIZE
25
28
32
KIT INCLUDES:
1 BRACKET FOR JC1STx SWITCH
1 MAGNETIC TARGET ASSEMBLY
1 SET SCREW FOR TARGET MOUNTING
1 SET SCREW FOR BRACKET
SIZE
19 25, 28, & 32
in-oz Nm in-oz
40 .28 40
— — 80
— — 59
1.0 —
— — 59
— — 14
— — 16
P.O. Box 9070, Fort Wayne, IN 46899
www.phdinc.com
1-800-624-8511 • 260-747-6151
6441-485D
CU
TARGET PIN
MAGNETIC
TARGET ASSEMBLY
MOUNTING KIT
SOLID STATE
81833-25
81833-28
81833-32
Nm
.28
.56
.42
—
.42
0.1
.11