Advertisement
4.4.
To lower load, put your hand on release valve and turn slowly anti-clockwise. This crane is fitted with a ‘dead man’ control which stops
the descent when your hand leaves the release knob.
4.5.
The crane is not a transportation device but may be used to reposition the load ready for working on. To do so lower the load and jib
to the lowest possible point before attempting to move. Do not attempt to move in a sideways direction.
The crane is not designed to sustain the load indefinitely.
When you have positioned the load for working, fully lower the load onto a secure and appropriate working base, being aware of your
own and other persons locations in relation to the lowering load.
4.6.
When the load has been successfully lowered and secured, remove the lifting harnesses etc., and place the crane in a safe location
having ensured the lifting beam and pistons are fully retracted.
5. MAINTENANCE
NOTE: The crane MUST be maintained in accordance with these instructions.
5.1.
Always keep the crane clean and dry.
5.2.
Lubrication
5.2.1. Oil all working parts monthly.
5.2.2. The ram is filled with oil and should only require occasional topping up. For the occasional top up DO NOT use brake fluid, as this
will damage the hydraulic seals, proceed as follows:
a) Use only good quality hydraulic jack oil available from your Sealey dealer.
b) Fully lower the jib extension arm.
c) DO NOT OVERFILL as this will cause failure.
d) After filling with hydraulic oil, pump the crane up to its full height and pour off any excess oil.
5.3.
Inspection of crane before use
5.3.1. Before each use of the crane you must make a visual inspection of the crane for leaks, damage, loose or missing parts.
5.3.2. The workshop crane must be inspected immediately if it has been subject to an abnormal load or shock.
It is recommended that such an inspection is made by the supplier’s authorised service agent.
5.3.3. The owner and/or operator must be aware that repair of this equipment will require specialised knowledge and facilities.
It is recommended that an annual inspection of the workshop crane is made through the supplier’s authorised service agent.
5.4.
Storage
Always store the crane with the jib is in its lowest position and the ram closed.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE MACHINE.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.
If product is under guarantee please contact your dealer.
6. OWNER’S & OPERATOR’S RESPONSIBILITIES
The owner and/or operator shall study product instructions and retain them for future use.
6.1.
Understanding Instructions & Warnings
The owner and/or operator shall understand the product operating instructions and warnings before operating the crane. Warning information
must be emphasised and understood. If the operator is not fluent in English, the product instructions and warnings must be read to and
discussed with the operator in the operator’s native language by the purchaser/owner, making sure that the operator understands the content.
6.2.
Damage
Any crane which appears to be damaged, badly worn, or operates abnormally MUST BE REMOVED FROM SERVICE! It is recommended
that necessary repairs be made by the supplier’s authorised service agent.
6.3.
Decommissioning
Through years of normal wear, the crane will eventually come to the end of its safe serviceable life. If, and when, this happens ensure the
hydraulic oil is drained off and disposed of in accordance with local authority regulations.
6.4.
Test Certificate
According to requirements of the UK Health and Safety Executive, a test certificate is packed with this crane. The test certificate is valid for
one year from the date of first placing the crane into use. Your insurance company will want to have a copy of the test certificate for their file.
Additional copies of the test certificate can be purchased within one year of the date of supply. If you need a copy please ask your dealer.
After one year your insurance company has the right to request a re-test of the crane. This is a chargeable service and can be obtained by
contacting companies listed under “Lifting Gear” in Yellow Pages.
7. CRANE GUARANTEE & D of C
Your crane is guaranteed for one year from the date of purchase. The Guarantee does not cover faults caused by incorrect use, lack
of maintenance or accidental damage, or damage caused to third parties through misuse. You are recommended to inform your insurers
and check that adequate cover is in place. Warranty claims must be supported by a copy of the dated receipt for goods.
Folding Crane
Models 500KCA, 750VA & WF10.
98/37/EC, Docks regulations 1934, 18a 22a EN292-2
Model No:
Serial No:
Batch No:
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group,
Bury St. Edmunds, Suffolk.
Declaration of Conformity
here are in conformity with the following standards and directives.
The construction files for these products are held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
01284 703534
01284 757500
We, the sole importer into the UK, declare that the products listed
14th July 2002
sales@sealey.co.uk
e-mail
500KCA/750VA/WF10 - 3 - 181202
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Quality Machinery.
www.sealey.co.uk
9A>
Advertisement
