Related Manuals for Canon BS1
Summary of Contents for Canon BS1
- Page 1 August 22, 2012 Revision 0 Puncher Unit-BS1 Service Manual Product Outline Technology Parts Replacing and Cleaning Installation...
- Page 2 This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may changes in the contents of this manual over a long or short period, Canon will issue a new not be copied, reproduced or translated into another language, in whole or in part, without the edition of this manual.
- Page 3 Explanation of Symbols The following rules apply throughout this Service Manual: The following symbols are used throughout this Service Manual. Each chapter contains sections explaining the purpose of specific functions and the Symbols Explanation Symbols Explanation relationship between electrical and mechanical systems with reference to the timing of operation.
-
Page 4: Table Of Contents
Contents Safety Precautions Installation Procedure --------------------------------------------------------4-4 Adjustments --------------------------------------------------------------------4-9 Notes Before Servicing ------------------------------------------------------0-2 Punching Operation Settings --------------------------------------------------- 4-9 Points to Note at Cleaning --------------------------------------------------0-2 Adjustment of Paper Stop Positiom. -----------------------------------------4-10 Affixing the Labels ---------------------------------------------------------- 4-11 Product Outline Specifications ------------------------------------------------------------------1-2 Hole Locations ------------------------------------------------------------------------------- 1-2 Names of Parts ----------------------------------------------------------------1-3 Cross Section ----------------------------------------------------------------------- 1-3 Technology... -
Page 5: Safety Precautions
Safety Precautions ■ Notes Before Servicing ■ Points to Note at Cleaning... -
Page 6: Notes Before Servicing
Safety Precautions Safety Precautions > Points to Note at Cleaning Notes Before Servicing Caution: At servicing, be sure to turn off the power source according to the specified steps and disconnect the power plug. Caution: Do not turn off the power switch when downloading is under way. Turning off the main power switch while downloading is under way can disable the machine. - Page 7 Product Outline ■ Specifications ■ Names of Parts Product Outline...
-
Page 8: Product Outline Specifications
A4 / A3 : 92.5±1mm LDR,LTR, LGL,LTRR,EXE indeterminate form 2 hole) 182 to 432 x 182 to 297 3 hole) 182 to 432 x 240 to 297 [2] Puncher Unit-BS1 (2/3穴) [3] Puncher Unit-BT1 (2/4穴(FR)) 4 hole(Puncher Unit-BU1) A3,A4 indeterminate form... -
Page 9: Names Of Parts
Product Outline > Names of Parts > Cross Section Names of Parts Cross Section F-1-2 Punch Motor Punch chip case full sensor Punch chip case Stopper Product Outline > Names of Parts > Cross Section... -
Page 10: Technology
Technology ■ Feed Drive System Technology... -
Page 11: Overview
Technology > Feed Drive System > Overview Feed Drive System Finisher Controller PCB J130 J131 Overview PS40 PS38 Punch Chip Punch Motor The machine punches holes in paper when the paper has been stacked in the finisher and Case Sensor Clock Sensor stopped. -
Page 12: Moving The Paper
Technology > Feed Drive System > Moving the Paper 2) When the inlet sensor detects the lead edge of paper, the machine moves the paper over a Moving the Paper specific distance and then uses the shift transport motor to drive the shift roller. Inside the machine, paper is moved as follows: Shift Shift Transport... -
Page 13: Checking The Condition Of The Punch Chip Case
Technology > Feed Drive System > Checking the Condition of the Punch Chip Case Checking the Condition of the Punch Chip Case 4) After correcting displacement in horizontal registration, the machine uses the shift transport motor to move the paper back to the punch unit and, at the same time, executes full The punch chip case detection mechanism consists of the punch chip case full sensor horizontal registration, in which the edge of the paper hits the stopper mounted to the mounted to the side of the punch chip case and a prism found inside the case. - Page 14 Technology > Feed Drive System > Checking the Condition of the Punch Chip Case Technology > Feed Drive System > Checking the Condition of the Punch Chip Case...
-
Page 15: Parts Replacing And Cleaning
Parts Replacing and Cleaning ■ Removing from the Host Machine ■ Drive System Parts Replacing and Cleaning... -
Page 16: Removing Punch Unit
Parts Replacing and Cleaning > Removing from the Host Machine > Removing Punch Unit Removing from the Host Machine 3) Remove the rear cover [1]. • 8 screws [2] Removing Punch Unit 1) Open the front cover [1] of finisher. F-3-3 F-3-1 2) Pull out the punch dust container [1]. - Page 17 Parts Replacing and Cleaning > Removing from the Host Machine > Removing Punch Unit 4) Remove the 2 connectors [2] connected to the finisher controller [1]. 6) Remove the punch unit [1]. • 2 screws [2] F-3-4 5) Remove the cable of the punch unit. •...
-
Page 18: Drive System
Parts Replacing and Cleaning > Drive System > Remove the punch unit > Procedure Drive System 3) Remove the gear[1] and Punch motor[3] • 2 screws [2] Remove the punch unit ■ Preparations 1) Remove the punch unit. ■ Procedure F-3-9 1) Remove the sensor plate [1]. -
Page 19: Installation
Installation ■ How to check this Installation Procedure ■ Points to Note at Installation ■ Checking the Contents ■ Check Items when Turning OFF the Main Power ■ Installation Procedure ■ Adjustments ■ Affixing the Labels Installation... -
Page 20: How To Check This Installation Procedure
When Using the Parts included in the package CAUTION: • This manual has been issued by Canon Inc. for qualified persons to leam technical A symbol is described on the illustration in the case of using the parts included in the package theory, installation, maintenance, and repair of Products. -
Page 21: Checking The Contents
Installation > Check Items when Turning OFF the Main Power Checking the Contents Check Items when Turning OFF the Main Power Check that the main power is OFF. [2] Punch dust box unit [3] Punch dust box [1] Punch unit X 1 1) Turning off the Main Power Supply Switch of the Host Machine. -
Page 22: Installation Procedure
Installation > Installation Procedure Installation Procedure 1) Open the Front Cover. Knobs Claw F-4-6 3) Lift the Upper Cover in the direction of the arrow and remove the Inner Cover (upper). • 4 Screws Inner Cover (Upper) Upper Cover F-4-4 2) Push the claw in the direction of the arrow [A] and remove the 3 knobs in the direction of the arrow [B]. - Page 23 Installation > Installation Procedure Positioning Pin 4) Remove tapes from contents. Punch Box Frame Unit 5) Separate the Punch Dust Box Frame Unit and the Punche Dust Box Unit. Punch Dust Box Frame Unit Punch Dust Box Unit Hole Punch Box Frame Unit Punch Box Frame Unit...
- Page 24 Installation > Installation Procedure 7) Remove the Rear Cover. 9) Insert the Punch Unit in the direction of the arrow from the back. • 2 Screws (Loosen) • 2 Screws (removed in step 8)) • 6 Screws CAUTION: When inserting the Punch Unit, avoid catching the belt with the Guide Plate. NOTE: Align the Guide Plate of the Finisher with the groove of the Punch Unit.
- Page 25 Installation > Installation Procedure Insert the connector of the Punch Unit into the connector on the Punch Dust Box Cut the 2 Face Covers of the Inner Cover (upper) with nippers. Frame Unit to fix the Cable. CAUTION: • 1 Cable Guide •...
- Page 26 Installation > Installation Procedure Insert the Punch Dust Box Unit in the direction of the arrow from the front. Punch Dust Box Unit F-4-17 Close the Upper Cover. Close the Front Cover. Install the Rear Cover. • 8 Screws Connect the Host Machine with the Finisher referring to Installation Procedure of the Finisher.
-
Page 27: Adjustments
Installation > Adjustments > Punching Operation Settings Adjustments SW381 punch unit not used Punching Operation Settings 1 2 3 4 5 6 7 8 NOTE: 2/3-hole punch unit used Depending on the Punch Unit to install, you may need to make settings of the DIP 1 2 3 4 5 6 7 8 Switch on the switch PCB found in the Finisher. -
Page 28: Adjustment Of Paper Stop Positiom
Installation > Adjustments > Adjustment of Paper Stop Positiom. 4-10 Adjustment of Paper Stop Positiom. 2) Remove the Switch Cover. To ensure the skew correction for paper edge skew dure to swithback, execute adjustment for • 1 Screw paper-stop position before starting switchback from the stopper. Stop position of paper Stopper Switch Cover... -
Page 29: Affixing The Labels
Installation > Affixing the Labels 4-11 Affixing the Labels 4) When executing punching operation in this condition, the paper stops without switchback and holes are punched. 1) Open the Front Cover. 5) Measure the dimension [A] between the hole position of the punched paper and the paper 2) Affix the Operation Label and the Jam Recovery Label.