Table of Contents
Advertisement
Setting the Clock
This unit incorporates a 24-hour clock. The clock must be set
for the Timer Recording function to operate correctly.
• Use the remote control for this procedure.
1) Press
VCR
, then
MENU
2) Press
or
to select "INITIAL", then press
K
L
3) Press
or
to select "CLOCK", then press
K
L
4) Press
or
until the relevant year appears, then press
K
L
5) Press
or
until the relevant month appears, then press
K
L
.
B
6) Press
or
until the relevant day appears, then press
K
L
7) Press
or
until the relevant hour appears, then press
K
L
8) Press
or
until the relevant minute appears.
K
L
9) Press
MENU
to start the clock.
Note:
• Press
to go one step back from the current step during
s
5)
8)
steps
to
.
• Although seconds are not displayed, they begin counting
from 00 when you exit by pressing
to synchronize the clock with the correct time.
• If this unit is unplugged or if there is a power failure for
more than 30 seconds, you may have to reset the clock.
MENU
TIMER
SET UP
INITIAL
Channel Presetting
Tuning of broadcast channels not already preset in the DVD/
VCR can be performed in two ways.
Automatic Channel Preset
• By "AUTOMATICALLY" tuning channels and placing
them in sequential order in the DVD/VCR's memory i.e.
the first channel found will be memorized into the DVD/
VCR's channel position 1, the second channel found will
be memorized into the DVD/VCR's channel position 2
and so on.
• Execution of the "Automatic" channel presetting cancels all
the preset channels. DO NOT use this feature if you intend
to use some of the pre-tuned channels. Use the "Manual"
channel presetting function to tune in the additional
channels you require.
Manual Channel Preset
• Each channel is tuned manually and individually. Follow
the steps laid out in the "Manual Channel Preset".
Before you preset Channel...
• It is necessary to set the video channel if this unit is
connected to the TV via the coaxial cable, and TV channel
35 is set for broadcasting, or interference lines appear on
the picture. Please refer to "Video Channel Setting".
.
.
B
.
B
MENU
. Use this feature
INITIAL
CH TUNING
CLOCK
RF OUT
CLOCK
YEAR
2 0 0 4
MONTH
0 1
DAY
0 7 WE
_ _
HOUR
_ _
MINUTE
Automatic Channel Preset
You can programme the tuner to scan only the channels that
you can receive in your area.
• Use the remote control for this procedure.
1) Turn on the TV and select the TV channel to the video
channel on the TV.
VCR
2) Press
, then
3) Press
.
or
to select "INITIAL", then press
B
K
L
4) Press
or
to select "CH TUNING", then press
K
L
5) Press
or
to select "AUTO", then press
K
L
.
• The tuner scans and memorizes all the active channels in
B
.
your area. After scanning, the tuner stops on the lowest
B
memorized channel.
MENU
TIMER
SET UP
INITIAL
To Select a Desired Channel
You can select a desired channel by using
directly pressing the
• Enter a channel numbers as a two-digit number for the
quickest results. For example, to select channel 6, press
6
and
. If you only press
brief delay.
• You can only select channels 1–99.
10
MENU
.
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
scanning
CH.
number buttons
on the remote control.
6
, channel 6 will be selected after a
.
B
.
B
.
B
(
/
), or
K
L
0
EN
Advertisement
Table of Contents
