Table of Contents
Advertisement
Defrosting
After a period of use, a thin layer of frost will be formed on the freezer compartment inner wall (or evaporator) surface, which may affect
the refrigeration effect if exceeding 5mm in thickness. In such case, you need to gently scrape the frost off using an ice scraper rather
than the metal or sharp hardware. Frosts need to be cleared off every 3 months or so, and if the normal use of drawers and normal
access of foods are affected by frosting, make sure to remove the frosts in a timely manner. Follow the following steps to remove frosts:
1、Take out the frozen foods, shut off the mains power supply, open the refrigerator door, and gently remove the frosts from the inner
wall with an ice scraper. To speed up the thawing process, you are suggested to place a bowl of hot water inside the refrigerator/freezer,
and when the solid ice frosts become loose, use an ice scraper to scrape them off and then take them out.
2、After defrosting, clean the refrigerator/freezer inside, and switch on the power supply.
Changing the lamp
The LED lamp is used by the refrigerator for lighting, which features low energy consumption and long service life. In case of any
abnormality, please contact the after-sales personnel for visiting service. The lamps can only be replaced by the manufacturer, together
with a part of the appliance.
Ⅶ. The following are not faults and Defrosting
△When the freezer is working or after is stops for a while, the refrigerant in the pipes is cycling and gives out＂running
water＂sounds.
△The surface temperature of the compressor may be up 70℃~95℃ when it is working.
△The back side of step freezer gives out heat.
△In rainy season, the outer surface of the cabinet may have dew, which makes no defects on normal use. Just dry it with
a piece of cloth.
△Defrost for better freezing efficiency when the frost film in the cabinet is 4-5mm thick.
△When thawing, turn off the power, take out the frozen food, open the door and let it melt naturally. Wash with water
and a soft cloth.
△Do not use sharp metal tools such as steel brush to clean the frost film when defrosting so as to avoid evaporator
Ⅷ.Trouble shooting
With regard to the following small faults, not every failure needs to be fixed by the technical service personnel; you can try to solve the
problem.
Breakdown
The indicator is not on.
The compressor doses not start.
The indicator is on ,but the com- pressor doesn't
work and buzzes only
The compressor stops a minute after start, and
restart after a few minutes, and so repeatedly.
The compressor works normally,
but the temperature in the cabinet
lowers too slowly.
The noise is too loud
Note: If the above descriptions are inapplicable to troubleshooting, do not disassemble and repair it yourself. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact the local store where your purchase was made. This product
should be serviced by an authorized engineer and only genuine spare parts should be used.
When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving
the door ajar to prevent unpleasant smells.
Locks
If your Refrigerator (freezer) is fitted with a lock, keep the key out of reach and not in the vicinity of the appliance to
prevent children being entrapped. When disposing of an old Refrigerator (freezer), break off any old locks or latches as a
safeguard.
Case
The plug isn't connected to the socket really.
no power
The power voltage is＜187V.
The power voltage is＞242V.
The door is opened too frequently.
The food in the cabinet is too
much, and placed improperly.
The frost film is too thick.
The surface of the condenser is too dirty.
The door seals badly.
The freezer is placed unstably.
The fixing of the freezer is loose.
there's contact between pipes.
7
Removal method
Re-plug it.
Connect the socket with power.
Put a power-regulator more than
1000W power together.
Reduce open times.
Place foods properly keep place
between them for ventilation of
cold air.
Take out foods and defrost.
Stop and clean the condenser.
Adjust the door seal.
Place it stably.
Tighten the fixing.
Separate them.
Advertisement
Table of Contents
