Delta 36-851 Instruction Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

STOCK FEEDERS

Models 36-851, 36-852,

36-855, and 36-856

Models 36-851 single phase

& 36-852 three phase

Models 36-855 single phase

& 36-856 three phase

PART NO. A08479 - 05-31-05

To learn more about DELTA MACHINERY

visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance,

1-800-223-7278 (

1-800-463-3582).

please call

In Canada call

Table of Contents

Summary of Contents for Delta 36-851

Page 1 & 36-852 three phase Models 36-855 single phase & 36-856 three phase PART NO. A08479 - 05-31-05 Copyright © 2005 Delta Machinery To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582).
Page 2: Table Of Contents
NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised you.
Page 3: Safety Guidelines
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protect- ing YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Page 4: General Safety Rules
Damage to the machine and/or injury may result. the dust exposure, and wash exposed areas with soap and 13. USE RECOMMENDED ACCESSORIES. The use of water. accessories and attachments not recommended by Delta may cause damage to the machine or injury to the user.
Page 5: Additional Specific Safety Rules
ADDITIONAL SPECIFIC SAFETY RULES FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. NEVER PERFORM LAYOUT, assembly, or set-up work DO NOT OPERATE THIS MACHINE until it is completely on the table/work area when the machine is running. assembled and installed according to the instructions.
Page 6 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protect- ed with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug.
Page 7: Functional Description
FUNCTIONAL DESCRIPTION FOREWORD The Delta Model 36-851 four-speed, three-roller Stock Feeder is powered by a 1 hp, 240V, single-phase, reversing motor. This unit comes with 3 rubber feed rollers, vertical and horizontal support columns, universal joints, and a lubricating gun.
Page 8: Operation
ASSEMBLING THE STOCK FEEDER 1. Loosen the locking handle (C) Fig. 3 and insert the vertical arm (D) of support assembly into the mount- ing bracket (A). 2. Tighten the locking lever (C) Fig. 3. 3. Loosen the locking handle (E) Fig. 3, and slide the horizontal arm (F) into the casting (G).
Page 9 FEED RATE ADJUSTMENTS (For 36-851 single phase and 36-852 three phase models ONLY!) These stock feeders utilize feed rates of 13, 26, 36 and 72 feet per minute or 4, 8, 11 and 22 meters per minute. You can find the gear arrangement and feed rate chart attached to the inside cover (A) Fig. 6 of gear box.
Page 10 The stock feeders use a two speed reversing motor (B) Fig. 11 to provide high and low speed/feed rates and to reverse the direction of feed. When you rotate the motor control switch (A) Fig. 11 to the "turtle" (C), the feed rates are 6.5, 18, 22 and 55 FT/MIN (2, 5.5, 6.7 and 16.5 M/MIN), depending on the gear arrangement and gear lever position When you rotate the motor control switch (H) Fig.
Page 11 ADJUSTING OPERATING POSITIONS DISCONNECT MACHINE FROM THE POWER SOURCE! You can rotate the entire feeder assembly (A) Fig. 15 360 degrees in the mounting bracket (B) by loosen- ing the locking lever (C). To raise or lower the feeder assembly (A) Fig. 15, loosen the locking lever (D) and rotate the hand- wheel (E).
Page 12: Troubleshooting
TROUBLESHOOTING For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). MAINTENANCE FEED ROLLER REPLACEMENT DISCONNECT MACHINE FROM THE POWER SOURCE! You can remove each feed roller (A) Fig.
Page 13: Service
SERVICE PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network • of Porter-Cable Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the loca- tion of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Page 14: Warranty
Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the prod- uct prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.
Page 15 NOTES...
Page 16 Phone: (514) 336-8772 Fax: (604) 420-3522 Fax: (514) 336-3505 The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ®...

This manual is also suitable for:

36-852 36-855 36-856