Summary of Contents for Triax IPTV EPG Server
- Page 1 User Manual IPTV EPG Server Article Article no. IPTV EPG Server 492095 Version V1.1 Date 2021/11...
-
Page 2: Table Of Contents
3.1 Introduction ..............................5 3.2 Packing contents .............................. 5 3.3 Technical data ..............................6 4 Mounting the IPTV EPG Server ....................... 7 4.1 Installing the device ............................7 4.2 Device overview ............................... 7 5 Installation & Easy Setup ........................ 8 5.1 Installation ............................... -
Page 3: Safety Regulations And Notes
IPTV EPG-Server 1 Safety regulations and notes ATTENTION • Failure to comply with the specified precautionary measures may cause serious injury to persons or damage to property. • The assembly, installation, additional electrical wiring, servicing installation and commissioning may only be performed by suitably qualified persons, technicians or installers in compliance with safety regulations. - Page 4 IPTV EPG-Server • Install the unit in a dry location without infiltration or condensation of water. In case of the formation of condensation wait until the system is completely dried. • Do not expose it to dripping or splashing. • If any liquid should accidentally fall into the cabinet, disconnect the power plug.
-
Page 5: Revision History
3 IPTV EPG Server 3.1 Introduction The IPTV EPG Server provides Middleware Solutions for Hotel IPTV systems with an eXtensive Markup Language (XML) file with the EPG data, normally contained in a DVB Transport Stream Barker Channel from satellite, cable and terrestrial antenna input to the TDX. -
Page 6: Technical Data
IPTV EPG-Server 3.3 Technical data Type IPTV EPG Server Art. no 492095 Functionality EPG XML Server for IPTV I/O RJ45 Ethernet Connector Mbps Supported speed 10/100/1000 Cable Category Cat 5e, Cat 6, Cat 7 Maximum Cable Length Input USB AUX... -
Page 7: Mounting The Iptv Epg Server
IPTV EPG-Server 4 Mounting the IPTV EPG Server 4.1 Installing the device The IPTV EPG-Server can be mounted in a 19” rack or wall mounted in any direction needed. 4.2 Device overview... -
Page 8: Installation & Easy Setup
IP addresses. 5.1.2 Connecting to the EPG Server Connect IPTV EPG Server to power. Using a computer on the same local network, type in the Server IP (default: http://192.168.0.200) into a browser to access the EPG Server Web Interface. -
Page 9: Status
IPTV EPG-Server 5.3 STATUS The Server Status page, gives basic information about the server. Take special note of the “Services” and “Events” fields. These show how many services the server is currently receiving data for, through the Barker channel. This number may differ from the number of services, reported by the TDX, since not all services actually have EPG data in their transport stream. -
Page 10: Settings
Barker channel. The IPTV EPG Server IP can be changed to a different subnet (e.g. the same as the TDX Service port). You can do so by changing it under “IP Settings”. It is not a necessary for the IPTV EPG Server to be on the same subnet as the TDX AUX port, they simply need to be connected to the same switch. -
Page 11: How To Change From Sinc To Reach Xml Format
IPTV EPG-Server To update the IPTV EPG Server, click select file and in the dialog box, select the image file you received from Triax A/S. Select Open and return to the Software Upgrade page. The click the Upgrade button and wait for the IPTV EPG Server to restart. -
Page 12: Security
Default session timeout is infinite, but if the page is accessed from another PC, the password needs to be entered again. 5.6 SOFTWARE UPGRADE The IPTV EPG Server can be updated via the Ethernet port. This is done by going to the Software Upgrade page. -
Page 13: How To Do An Initial Install (Normal Update Not Working)
IPTV EPG-Server To update the IPTV EPG Server, click select file and in the dialog box, select the image file you received from Triax A/S - “xmls_fw_1.1.9.img”. Select Open and return to the Software Upgrade page. Then click the Upgrade button and wait for the IPTV EPG Server to restart (it can take up to 2 minutes). -
Page 14: Misc
5.8 Output format The function of the IPTV EPG Server is to translate the data provided by the TDX via the Barker channel to the supported XML file formats. The Barker channel itself does not contain the service names, but provides EPG data for each ONID/TSID/SID, i.e. -
Page 15: Xmltvformat
5.9 Information necessary for the Middleware Server The IPTV EPG Server is designed to provide EPG data to an IPTV Hospitality TV or Set Top Box. In these setups, the Middleware Server controls the channel mapping for the TVs, and the only channel information the IPTV EPG Server can extract from the Barker stream, is the Original Network ID (ONID), the Transport Stream ID (TSID) and the Service ID (SID). -
Page 16: Samsung Sinc Server And Reach Server
EPG data as long as you know the SID. Note that the SIDs are delivered in HEX numbers from the IPTV EPG Server. This means that the number 10 is represented as an A, the number 11 is represented as a B and the number 15 is represented as an F. -
Page 17: Support
IPTV EPG-Server 6 Support Support information in your language will be found on our country sites. Go to www.triax.com and select your country. Below the Support & Training menu you will find additional help and support information. -
Page 18: Terms And Abbreviations
IPTV EPG-Server 7 Terms and Abbreviations Term Explanation To Be Added To Be Determined Packet Identification; According to standard ISO 13818-1 Service Identification; According to standard ISO 13818-1 TSID Transport Stream Identification Network Identification Table; According to standard ETSI EN 300 468 Network Identification used in NIT;...