Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Schweigen Isodrive 650
Summary of Contents for Schweigen Isodrive 650
- Page 1 INSTALLATION GUIDE Isodrive 650 www.schweigen.com.au Revision V2 25/11/21...
-
Page 2: Welcome
Welcome Thank you for purchasing your new Schweigen Isodrive system. To get the maximum output from this unit, please read through this guide before use and installation. This guide contains important information on the correct use and maintenance of the unit, as well as important safety notes. -
Page 3: Table Of Contents
Back Draft Shutter System Fitment to Bell-mouth Adaptor __________________________________ 15 6. Installation Examples Single Motor Installation Example ________________________________________________________________ 16 Twin Motor Installation Example _________________________________________________________________ 17 7. Measurements Measurements for Isodrive 650 ______________________________________________________ 18 8. SteelFlex Safety Duct ™ SteelFlex Safety Ducting Installation _________________________________________________ 19 ™... -
Page 4: Your Safety
Children should be supervised to ensure that they do not play with the appliance, it is not a toy. Do not install Isodrive motor to a non-Schweigen and/or non-silent rangehood. If you fail to do so, your warranty will be voided. -
Page 5: Motor Features
NOTE: Fan module and dual foil Steelflex duct are acoustically matched. Use of semi-rigid or rigid ducting will ™ result in increased noise and may void warranty. See installation instruction notes ‘Why Schweigen SteelFlex ™ Safety Duct’ . Recommended Installation Distance Isodrive 650 motor, recommended minimum 3 metres (approx.) of SteelFlex... -
Page 6: Minimum Mounting Height
Any installation problem must be reported ™ to Schweigen. Call outs relating to incorrect installation will result in a service fee direct to the customer. Schweigen takes no responsibility for problems caused by faulty installation, this may void warranty. A preferred installer list can be obtained from Schweigen website www.schweigen.com.au or by calling... -
Page 7: Description
19. ™ Isodrive Motor Included in the box: Isodrive 650 motor (280W x 200H mm approx.) Approx. 3 metre, 10amp cable and standard male plug Fire resistant 100mm (110mm OD ) PVC riser pipe Note: Cable cut-out at the bottom end only... -
Page 8: Installation
4. Installation Roof Installation Recommended duct length: 650 motor — 3 metres. Mount 100mm rigid PVC pipe securely to beams, trusses or other appropriate structures: refer figure 1. The pipe should be mounted vertically or perpendicular to the roof cladding with the roof penetration being sealed using a Dektite or other appropriate sealing membrane or device. - Page 9 4. Installation Roof Mount Option Ensure clearance Mounting Flange 100 — 400 100mm PVC Pipe Dektite Eaves Mount Option Bell-mouth adaptor Connect to rangehoood Slot option Connect to rangehood Min 90mm long PVC pipe Bell-mouth adaptor To fan Electrical connection between rangehood and remote fan module Wall Mount Option...
- Page 10 4. Installation Roof Installation Locking Screw Fan Module Roof Clading Mounting Flange Dektite Slot option Roof Frame Optional 100mm PVC Pipe bend Secure pipe to structure Slot pipe for power cord exit. Cover with ducting 150mm SteelFlex ducting ™ tape if required 5 metre max Bell-mouth adaptor Connect to...
-
Page 11: Eaves Installation
4. Installation Eaves Installation After ensuring sufficient clearance exists for the mounting flange and ducting, refer figure 1, cut a circular hole 165mm Ø, maintaining adequate clearances. The eaves sheeting should be reinforced. Pre-drill mounting flange recess. Refer figure 3. If access to the eaves space is restricted, before fixing mounting flange to eaves, preassemble mounting flange, PVC pipe, bell-mouth adaptor and flexi-duct then feed up into roof space. -
Page 12: Wall Installation
4. Installation Wall Installation The installation should be similar to eaves mounting if access to the inside is limited, but if unrestricted. Refer to EAVES INSTALLATION and figure 4. Min 90mm long PVC pipe Min 20mm Bell-mouth Adaptor 150mm SteelFlex ducting ™... -
Page 13: Back Draft Shutter System
5. Back Draft Shutter System Back Draft Shutter System for 150mm Ducting This back draft shutter suitable for Isodrive 650 motor only. duct SteelFlex ™ To fan Use duct tape to secure SteelFlex ™ duct to shutter system Direction of... -
Page 14: Installation For Back Draft Shutter System (150Mm Ducting)
5. Back Draft Shutter System Installation Example for Back Draft Shutter System (150mm Ducting, refer to figure 5) This back draft shutter suitable for Isodrive 650 motor only. Vertical Installation Horizontal Installation Figure 6 shows an example of vertical If you have a narrow roof space, you can install installation. -
Page 15: Back Draft Shutter System Fitment To Bell-Mouth Adaptor
5. Back Draft Shutter System Back Draft Shutter System Fitment to Bell-mouth Adaptor This back draft shutter suitable for Isodrive 650 motor only. This back draft shutter system cannot be installed in eave type installation. Back draft shutter system Bell-mouth adaptor... -
Page 16: Installation Examples
6. Installation Examples Single Motor Installation Example Use smooth flowing curves for maximum airflow. Remove excess ducting by trimming to length. DO NOT install motor in straight line to rangehood. Connect to rangehood Connect to motor Connect to main power Cover Use reducer 150mm to 200mm Figure 10... -
Page 17: Twin Motor Installation Example
6. Installation Examples Twin Motor Installation Example Where two motors are to be used, follow the below methods for each motor then join into the “Y” piece prior to joining ducting to the canopy / rangehood. Refer figure 11. The two motors can be wired by one of the following methods: •... -
Page 18: Measurements
7. Measurements Measurements for Isodrive 650 (Not to Scale) 278mm 157mm 28mm 195mm 35mm 29mm 35mm minimum 110mm 370mm Figure 12 Page 18... -
Page 19: Steelflex ™ Safety Duct
Incorrect installation may reduce airflow or increase noise levels. Call outs relating to incorrect installation will result in a service fee directed to the customer. Schweigen will take no responsibility for problems caused by faulty installation. A list of preferred Schweigen installers can be obtained from the Schweigen website www.schweigen.com.au. -
Page 20: Assembling Steelflex ™ Safety Duct
8. SteelFlex Safety Duct ™ Assembling SteelFlex Safety Duct ™ SteelFlex safety duct must be secured to either the bell-mouth adapter ring or a 150mm mounting pipe. ™ Parts required: SteelFlex safety ducting ™ Steel ring clamp Bell-mouth adapter ring 150mm duct to 100mm riser 100mm PVC riser pipe 20mm self-drilling button head screws... -
Page 21: Shallow Roof Space
8. SteelFlex Safety Duct ™ Shallow Roof Space In shallow roof spaces, do not crush or kink SteelFlex ducting, as it will reduce air flow severely. 90 degree ™ curve made of PVC or galvanise can be used as a substitute for the bend, refer to figure 14. 90 degree curve PVC or galvanise curve Figure 14... -
Page 22: Installing Steelflex ™ Safety Duct
8. SteelFlex Safety Duct ™ Securing SteelFlex Safety Duct ™ SteelFlex safety duct must be installed with supports at maximum intervals of 1.5 metres. SteelFlex safety ™ ™ ductwork can be supported by using good quality gaffer or aluminium foil tape. Provided that it does not restrict the internal diameter of the ducting. -
Page 23: Maintenance
9. Maintenance Roof Restoration or Cleaning Before doing your roof restoration or cleaning, please completely cover the outside motor system and avoid all chemical contact. IMPORTANT Any damages caused by the use of chemical products are not covered by warranty. Figure 17 Avoid chemical contact to motor system Page 23... -
Page 24: Warranty/Disclaimer
All information supplied is to be used for general reference purposes only and is on the understanding that Schweigen Home Appliances will not be liable for any loss, liability or damage of whatever kind arising as a result of any reliance upon such information. All pictures used in the guide are for illustrative purposes only. - Page 25 Notes Page 25...
- Page 26 Notes Page 26...
- Page 27 Notes Page 27...
- Page 28 Australia Unit 4/1-5 Lake Drive, Dingley Village, Victoria 3172. Phone 1300 881 693 Email sales@schweigen.com.au Web www.schweigen.com.au New Zealand 5 Tolich Place, Henderson, Auckland 0610. Phone 0800 200 510 Email info.parex@emerson.com Web www.parex.co.nz...
Need help?
Do you have a question about the Isodrive 650 and is the answer not in the manual?
Questions and answers