Advertisement
Quick Links
Techno Inc.
INSTALLATION & SETUP TABLE OF CONTENTS
I.
Machine Identifi cations
II.
How To Use the Vacuum Table
III. Scale Factor Setup
APPENDICES
A.
Techno Electronics
B.
Colleting Guidelines
C.
Machine Maintenance
CUSTOMER SUPPORT WEBSITE
http://support.technocnc.com/
Visit this site for software updates
and the Tech-Support Wizard.
This Wizard is password protected
for our customers.
Username: technocnc
Password: multiaxis
Premium Class Setup Instructions
Phone: 516-328-3970 · Web: www.technocnc.com
HTT03170704
ADDITIONAL DOCUMENTATION
Can be found in the "More Manuals"
folder on your TECHNO CD-ROM.
Advertisement
Related Manuals for Techno Premium Series
Summary of Contents for Techno Premium Series
- Page 1 Colleting Guidelines Machine Maintenance ADDITIONAL DOCUMENTATION CUSTOMER SUPPORT WEBSITE Can be found in the “More Manuals” folder on your TECHNO CD-ROM. http://support.technocnc.com/ Visit this site for software updates and the Tech-Support Wizard. This Wizard is password protected for our customers.
- Page 2 Phone: 516-328-3970 · Web: www.technocnc.com HTT03170704 HAVE A LICENSED ELECTRICIAN PERFORM ALL ELECTRICAL CONNECTIONS BASED ON YOUR LOCAL CODES IMPORTANT: KEEP YOUR TECHNO CD-ROM. IT CONTAINS ADDITIONAL DOCUMENTATION. I. MACHINE IDENTIFICATIONS CNC Control Unit Wires CNC Control Unit Panel CNC Control Unit...
- Page 3 Techno Inc. Premium Class Setup Instructions HTT03170704 Phone: 516-328-3970 · Web: www.technocnc.com II. HOW TO USE THE VACUUM TABLE Vacuum Pump w/ Motor Starter Vacuum Pump Motor Starter Box & Connector Pump/Blower Cable You will need to connect the The signal connector needs...
- Page 4 Vacuum Hold-Down - 1 Vacuum Hold-Down - 2 After you have defi ned your workpiece The Techno Vacuum Table is very effective in area and closed off all the vacuum “holding down” parts to be routed. For this method outside of that area, there is another...
- Page 5 STEP 5: Click the OK button in the Setup/System screen to save the changes made. IF THE VALUES ARE NOT WRITTEN ON THE FRONT LEG OF YOUR TECHNO CNC ROUTER THEN THE INTERFACE DEFAULT VALUES SHOULD APPLY. Continue to next page …...
- Page 6 · Gantry III Machines WARNING: Make sure to match the correct PCI Card with the corresponding Techno Electronics. Mixing the Interface Card with the MP/HP Electronics, or using the Controller Card with the LP Electronics may cause damage to the Electronics, the PCI Card and your computer.
- Page 7 Techno Inc. Premium Class Setup Instructions Phone: 516-328-3970 · Web: www.technocnc.com HTT03170704 APPENDIX B Continue to next page …...
- Page 8 Premium Class Setup Instructions Phone: 516-328-3970 · Web: www.technocnc.com HTT03170704 APPENDIX C LUBRICATION SPECS FOR PREMIUM CLASS MACHINES AVAILABLE ACCESSORIES TECHNO LUBE KIT PART NO.: H90Z00-LUBEKIT3 PRICE: $75.00 THK LUBE KIT PART NO.: H90Z00-LUBEKIT4 PRICE: $105.00 Y-Axis – THK Products Grease: Lithium-based grease (JIS NO.
- Page 9 Techno Inc. Premium Class Setup Instructions HTT03170704 Phone: 516-328-3970 · Web: www.technocnc.com PREMIUM CLASS MACHINE MAINTENANCE 2. Apply grease to the the grease fi ttings on the ball nuts and the grease fi ttings located on the end bear- For regular work loads, machine maintenance is ings of the X-Axis and grease Z-Axis.
- Page 10 Techno Inc. Premium Class Setup Instructions Phone: 516-328-3970 · Web: www.technocnc.com HTT03170704 III. THK RAILS: THK specifi cations indicate that a small amount of grease needs to be applied to the rails after 4 months of use. The following pictures indicate the location of the grease fi...
Need help?
Do you have a question about the Premium Series and is the answer not in the manual?
Questions and answers