Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dahua N45EYN2
Summary of Contents for Dahua N45EYN2
- Page 1 Dome Network Camera Quick Start Guide V1.0.0...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, configuration, general operation, and system maintenance of network camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. -
Page 3: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical Safety ● All installation and operation shall conform to your local electrical safety codes. ● The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited Power Source requirement according to IEC60950-1. - Page 4 Quick Start Guide ● You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent to clean the device body, nor can strong, abrasive detergent be used.
-
Page 5: Table Of Contents
Quick Start Guide Table of Contents Foreword ........................................I Important Safeguards and Warnings ............................II 1 Introduction ......................................1 1.1 Cable ......................................1 1.2 Connecting Alarm Input/Output ............................2 2 Network Configuration ................................... 3 2.1 Initializing Device ................................... 3 2.2 Changing Device IP Address .............................. 5 2.3 Logging in to Web Interface ............................... -
Page 6: Introduction
Quick Start Guide 1 Introduction 1.1 Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see the FAQ Manual. Figure 1-1 Cables For more information about cable ports, see Table 1-1. Table 1-1 Cable information Port name Description... -
Page 7: Connecting Alarm Input/Output
Quick Start Guide Port Port Name Description ALARM_IN Receives the switch signal of external alarm source. ALARM_IN_GND Connect different alarm input devices to the same ALARM_IN_GND port. 1.2 Connecting Alarm Input/Output The camera can connect to external alarm input/output device through digital input/output. Alarm input/output is available on select models. -
Page 8: Network Configuration
Quick Start Guide 2 Network Configuration Device initialization and IP setting can be finished with the "ConfigTool" or on web interface. For more information, see the Web Operation Manual. ● Device initialization is available on select models, and it is required at first-time use and after device is being reset. - Page 9 Quick Start Guide The Device initialization interface is displayed. Select the devices to be initialized, and then click Initialize. Step 7 ● If you do not provide the reserve information for password reset, you can reset the password only through XML file. ●...
-
Page 10: Changing Device Ip Address
Quick Start Guide Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates according to the actual needs. If neither, leave them unselected. Step 10 Click OK to initialize the device. Click the success icon ( ) or the failure icon ( ) for the details. -
Page 11: Logging In To Web Interface
Quick Start Guide Figure 2-4 Modify IP address Step 3 Select Static mode, and then enter start IP, subnet mask, and gateway. ● IP addresses of multiple devices will be set to the same if you select the Same IP check box. -
Page 12: Installation
Quick Start Guide 3 Installation 3.1 Packing List ● The tool required for the installation such as electric drill is not provided in the package. ● The operation manual and related tool information are contained in the disk or the QR code, and the actual package shall prevail. -
Page 13: Installation Method
Quick Start Guide 3.3.1 Installation Method Figure 3-3 Installation method 3.3.2 Installing SD Card Disconnect the power before installing or removing the SD card. Press and hold the reset button for 10 seconds to reset the device. Figure 3-4 Install SD card 3.3.3 Attaching Camera ●... -
Page 14: Optional) Installing Waterproof Connector
Quick Start Guide Figure 3-6 Cable going through the side cable tray 3.3.4 (Optional) Installing Waterproof Connector This part is needed only when a waterproof connector comes with the camera and the camera is used outdoors. - Page 15 Quick Start Guide Figure 3-7 Install waterproof connector...
-
Page 16: Adjusting Lens Angle
Quick Start Guide 3.3.5 Adjusting Lens Angle Figure 3-8 Adjust lens angle... - Page 17 Dahua Technology USA 15245 Alton Parkway, Suite #100 Irvine, CA 92618 Tel: (949) 679-7777 Fax: (949) 679-5760 Support: 877-606-1590 Sales: sales.usa@dahuatech.com Support: support.usa@dahuatech.com © 2021 Dahua Technology USA. All rights reserved. Design and specifications are subject to change without notice.