RSG Standby S-HAL06 User Manual

131220F10
UNDERCOVER LED KIT

CONTENTS

6LED KIT
w/ Split Color

LIGHT ASSEMBLY INSTALLATION

1. Remove the Corner/Head/Tail light from vehicle.
2. Select location to mount lighthead.
3. Drill 1 inch diameter hole to the light assembly.
4. Insert lighthead into hole and rotate to achieve optimum effect.
5. Secure lighthead with supplied sheet metal screws.
6. Apply silicone (user-supplied) for better seal.
WARNING: Do NOT cover heat sink with silicone. It may cause
damage to the product and void warranty.

OPERATIONS

To +VDC (fuse @2A) for Color1
o Chassis Ground.......................................................BLACK
T
To +VDC (fuse @2A) for Color2
For Synchronization & Flash
Connect YELLOW wires of all Kits together for synchronization
*All kits must be set at the same pattern
For Simultaneous or Split Flash (single head):
1. Apply +VDC to RED and YELLOW wires simultaneously to enter Mode
selection; lighthead will display single flash.
2. Remove YELLOW wire from +VDC and momentarily apply to +VDC to change
Mode: Mode1 = Simultaneous Flash, Color1 and Color2 LEDs flash together.
(default)
Mode2 = Split Flash, Color1 LEDs alternate with Color2 LEDs.
Mode1 (Simultaneous Flash)
(Suitable for Single-Color Heads)
Flash
Color1&2 flash together,
Patterns
Head1 alternate Head2
#1~9
Flash
Color1&2 flash together,
Patterns
Head1&2 flash together
#10~17
Flash
Steady Half
Pattern
#18
Mode2 (Split Flash)
(Suitable for Split-Color Heads)
Flash
Color1 alternate Color2
Patterns
#1~9
Flash
Color1 flash together,
Patterns
Color2 flash together
#10~17
Flash
Steady Half
Pattern
#18
LIGHTHEAD x 2pcs EXTENSION CABLE
activation........................RED
activation...................WHITE
Patterns.......................YELLOW
Head1
Flash
Color1Color2
on on
1st
off off
2nd
on on
1st
off off
2nd
on on
1st
on on
2nd
Head1
Flash
Color1Color2
on off
1st
on
off
2nd
on
off
1st
on
2nd off
on on
1st
on
off
2nd
USER MANUAL
FLASHER & CABLE
Mounting screw holes
Head2
Color1Color2
For Flash Pattern change, momentarily apply +VDC
off off
to YELLOW
on on
on on
off off
1
on
on
2
off off
3
Head2
4
Color1Color2
5
off on
6
on
off
7
on
off
8
on
off
9
on on
on
off 10
NOTE:
GASKET x 2pcs FLANGE OPTION x 2pcs
SCREW x 4pcs
VEHICLE
CORNER LIGHT
ASSEMBLY
1 inch dia. hole
to lighthead
NOTE: Lighthead mounting location
may vary depending on the design of
the vehicle light assembly.
∙ once for next pattern
wire:
∙ quickly three times for reset
Flash Patterns
Random 11 Double (all)
Single (split) 12 Quad (all)
Double (split) 13 Quint (all)
Quad (split) 14 Mega (all)
Quint (split) 15 Ultra (all)
Mega (split) 16 Single-Quad (all)
Ultra (split) 17 Single H/L (all)
Single-Quad (split) 18 Steady Half
Single H/L (split) 19 Steady All
Single (all)
This unit may not be factory set at FP# 1.
FOAM x 2pcs
Gasket
Lighthead
Supplied sheet
metal screw