Table of Contents
Advertisement
Quick Links
Thank you for purchasing the new SI-H XL 500 Projector Lift.
The SI-H XL 500 is supplied with a set of components and accessories that make it suitable for installation for
the majority of standard AV applications, but note must be made of the restrictions that apply to the weight
capability of this unit and not exceeded.
BEFORE INSTALLING THE LIFT, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY. Please, always
keep these instructions so that anyone can read them when needed.
THE MANUFACTURER DOES NOT TAKE RESPONSIBILITY FOR ANY DAMAGE TO PROPERTY OR PERSONAL
INJURY IF THE PROJECTOR LIFT IS USED OUTSIDE OF RECOMMENDED SPECIFICATIONS OR IN CASE OF
INCORRECT INSTALLATION.
Before installing the projector lift, please read the following instructions carefully:
•
The projector lift must be used INDOORS ONLY.
INSTALLATION OF SI-H XL 500 PROJECTOR LIFT HAS TO BE CARRIED OUT FROM
QUALIFIED PERSONNEL ONLY.
•
IT IS FORBIDDEN TO STAY UNDER THE LIFT AND WITHIN A RANGE OF 3 MT. FROM THE
LIFT.
•
NEVER CONNECT MORE THAN ONE MOTOR TO THE SAME SWITCHER. USE THE
SUPPLIED REMOTE CONTROL ONLY.
•
IN CASE OF MAINTENANCE, UNPLUG THE POWER SUPPLY.
•
Please confirm that your projected image width will fit your screen from your proposed
mounting location prior to installation.
•
Incorrect use of the lift, including exceeding the maximum lifting weight, will be
dangerous. The manufacturer does not take responsibility for any damage o property or
personal injury if the lift is used outside of recommended specifications.
• Incorrect use of the projector lift, including exceeding the maximum lifting weight of 95
kg., would be dangerous and invalidates the warranty.
•
This product uses a 230V AC Motor. DO NOT attempt to service the motor. Incorrect
servicing could lead to risk of electric shock.
•
For any repairing, please contact directly the dealer you purchased the unit from.
•
DO NOT try to disassemble the lift or to paint the structure, as these operations will
invalidate the warranty.
•
Half-yearly and yearly the screen winch system has to be checked. Please see check
register at page 8 of this document.
•
In addition to manufacturer inspection guidelines, we recommend you check your
countries own legal obligations for checking and testing of lifting equipment.
The manufacturer and his agents do not take responsibility for any damage to property
or personal injury if the winch is installed/used outside of recommended
specifications.
This product uses a 230 V AC motor. DO NOT attempt to carry out repairs to
the motor, there are no user serviceable parts.
Incorrect servicing could lead to risk of electric shock. In the event of a
fault, please contact the dealer /supplier you purchased the lift from.
Warranty is 24 months Return To Base.
The projector lift SI-H XL 500 is
MOTORIZED PROJECTOR LIFT
MOD. SI-H XL 500
INSTALLATION MANUAL
certified.
(version OCT-2021)
1
Advertisement
Table of Contents
Related Manuals for Screenint SI-H XL 500
Summary of Contents for Screenint SI-H XL 500
- Page 1 Thank you for purchasing the new SI-H XL 500 Projector Lift. The SI-H XL 500 is supplied with a set of components and accessories that make it suitable for installation for the majority of standard AV applications, but note must be made of the restrictions that apply to the weight capability of this unit and not exceeded.
- Page 2 Warranty is officially voided if the lift has been dismantled or it is returned with collision damage or defective due to incorrect installation. Repairs must be carried out by an Approved ScreenInt Certified Engineer. Warranty is officially voided if (all the following cases are including but not limited): defects not due to deficiencies in the material or workmanship;...
- Page 3 In order to mount the four metal brackets shown on Fig. “B” above on the upper aluminium frame of the SI-H XL 500, please use screws, washers and crowned nuts mentioned on “C, D, E” of the supplied equipment list; put inside the groove of the aluminium frame the crowned nut as shown on Fig. 1A;...
- Page 4 FIXING THE PROJECTOR TO THE LIFT Roll down the SI-H XL 500 by pushing ▼ button on the remote control (Fig. 7A) in order to lower the lift till the lower end-stop (SERVICE mode), preset in the factory at 2,5 mt. ca. In case you wish to modify the lower end-stop (SERVICE mode), please refer to instructions at page 4 and 5.
- Page 5 ADJUSTMENT OF THE END STOPS PLEASE READ CAREFULLY The SI-H XL 500 motorized lift is supplied with a remote control that allows to set three positions: 1- CLOSED LIFT: preset by the factory, in closed upper position. WARNING: in case the installer needs to modify this end-stop, it is ONLY allowed to lower the upper end-stop position.
- Page 6 Close the connection, for at least 1 second, simultaneously between the white-black, white-orange and white wires in order to reach the INTERMEDIATE stop (PROJECTION mode). The SI-H XL 500 projector lift includes a CABLE MANAGEMENT SYSTEM. In order to fit in the power and signal cables of the projector Move the lift in the lower end stop position (SERVICE MODE), and open the small doors, as shown in Fig.
- Page 7 MOTOR SPEED 12 rpm ROLL UP/DOWN SPEED 17 sec./metre TERMICAL STOP after 4 minutes of operation NET WEIGHT LIFT SI-H XL 500 kg. 78 MAXIMUM LOAD OF THE PROJECTOR kg. 95 DIMENSIONS SI-H XL 500 CLOSED 790x716x890 (WxHxD in mm.) DIMENSIONS SI-H XL 500 OPENED 790x5716x890 (WxHxD in mm.)
- Page 8 PROJECTOR LIFT SI-HXL300/SI -HXL500-CHECKREGISTER In addition to manufacturer inspection guidelines, we recommendyou check your countries own legal obligations for checking and testing of lifting equipment. PROJECTOR LIFT SI-HXL 300/SI-HXL 500 PURCHASE DATE: HALF-YEARLY CHECK YEARLY CHECK CHECKRESULT DATE DATE (POSITIVE -NEGATIVE) NOTES HALF-YEARLYCHECK Checkif rolling up and rolling down is working properly, without frictions or decelerations.
Need help?
Do you have a question about the SI-H XL 500 and is the answer not in the manual?
Questions and answers