Page 1
SANTINO 7.0 OF PCT Cortex -A9 Rear Mount ® ® Product Manual...
Page 2
15.03.2018 Page 18 New Picture RS485 Pin 6 to 11 Page 17 add Text for Pin1, Page 15 add new 04.12.1018 Capitle 5.2 " connecting the HMI device" 26.08.2019 Change address 17.12.2021 SECO CI Update 2022 Online support on edge.seco.com...
SANTINO Introduction Thank you very much for purchasing a SECO Northern Europe product. Our products are dedicated to professional use and therefore we suppose extended technical knowledge and practice in working with such products. The information in this manual is subject to technical changes, particularly as a result of continuous product upgrades.
Please read this section carefully and observe the instructions for your own safety and correct use of the device. Observe the warnings and instructions on the device and in the manual. SECO Northern Europe embedded systems have been built and tested by us and left the company in a perfectly safe condition.In order to maintain this condition and ensure safe operation, the user must observe the instructions and warnings contained in this manual.
Type Plate and Device Information For service and later identification of the device, the type plate contains important information. Position of Typelabel 25,4 Art.No.: 900-0000R SECO Northern Europe article number Model: SANTINO x1 Product name and configuration S/N: YY-WW Production date (week/year)
PRODUCT MANUAL SANTINO Related Documents and Online Support This document contains operating system specific information. The following additional documentations are available: OPERATING SYSTEMS Contains information about Linux BSP with development environment Linux Yocto Jethro Linux Embedded System Yocto (Codename: Jethro, Version 3.0) includes first information about the bootloader Flash-N-Go https://bit.ly/3DjEihg Linux Yocto Rocko...
PRODUCT MANUAL SANTINO Technical Data i.MX6DualLite CPU Type i.MX6Solo Core Class Cortex ® ® Core Clock 1 GHz NEON for SIMD media acceleration and VFP operations; Multi-format HD 1080p Features video decoder and HD 720p video encoder hardware engine; L1 cache, 32 KB for instruction, 32 KB for data;...
Page 10
PRODUCT MANUAL SANTINO Housing Front 1.1 mm toughened glass Frame None Rear ABS-PC/1.4016 stainless steel Ingress Protection Front IP 20/Rear IP20 Device Dimensions W x H x D 185.1 x 101.6 x 33.28 mm Weight tbd. Power Supply Supply Voltage Nom.
PRODUCT MANUAL SANTINO Connectors As this manual describes an open frame version, only the external interfaces will be mentioned in the following chapter. L171 (Exemplary Illustration. It shows the fully equipped SANTINO Dualcore light 7.0" BX PCT.) Pos. Description GND Shield connector (X122) Ethernet (X118) Power (X1) CAN/RS-485 Interface (X39)
Page 13
PRODUCT MANUAL SANTINO (Exemplary Illustration both sides) Pos. Description Reset Switch (SW1) Bootselect Switch (SW2) SD card reader (X31) Power LED (D30) For the function of this switch please refer in the future to the Flash N Go User Manual.
PRODUCT MANUAL SANTINO Installation and Start Up The content of this document is limited to explain the device connectors and how to access SANTINO via FTP over your local area network (LAN) within a few seconds. For advanced hardware specifications and software support, please refer to chapter „3.3 Related Documents and Online Support“...
PRODUCT MANUAL SANTINO Connecting the HMI device Notice An incorrectly dimensioned power supply can destroy the HMI device. Use a DC power supply with adequate amperage; see Chapter 4. Technical Data Notice Safe electrical isolation For the DC supply, use only power supply units with safe electrical isolation in accordance with IEC 60364-4-41 or HD 384.04.41 (VDE 0100, Part 410), e.g.
PRODUCT MANUAL SANTINO Internal and External Interfaces GND Shield Connector (X122) Name Description Information Ground shield 6.3 mm spade terminal Ethernet (X118) Name Description Information Rx/Tx might be swapped (Auto-MDIX) SPARE 1 +/- might be swapped (Autom. polarity correction) SPARE 2 Header: RJ45 Green LED (link) is default off and turns on when link is detected.
PRODUCT MANUAL SANTINO Power (X1) Name Description Level DC Ground Vcc_In DC Input voltage Nom. 9 to 32 V DC Header: Molex 43045-0200 Micro-Fit 2p Plug: Molex 43025-0200 Micro-Fit 2p, crimp contact Molex 43030-0007 Shielding with 6,3 mm male spade terminal connector. Pin 1 (GND) is connected to frame/housing.
PRODUCT MANUAL SANTINO CAN/RS-485 Interface (X39) Name Description Level GND_CAN_RS485 Ground Shield CAN1_TERM To enable CAN1-Termination, bridge with CAN1_H CAN1_H CAN bus 1 high +24 V CAN1_L CAN bus 1 low +24 V CAN1_TERM To enable CAN1-Termination, bridge with CAN1_L RS485_TERM To enable RS485-Termination: bridge with RS485_A CAN1 Termination...
PRODUCT MANUAL SANTINO USB Host (X34) Name Description Level USB_H1_VBUS Power supply +5 V DC max 500 mA USB_H1_DN Data minus (D-) USB_H1_DP Data plus (D+) Ground Header: USB Type A 6.10 USB OTG (X20) Name Description Level USB_OTG_VBUS Power supply +5 V DC max 100 mA USB_OTG_DN Data minus (D-)
PRODUCT MANUAL SANTINO 6.12 Reset Switch (SW1) Push for a power on reset. 6.13 Bootselect Switch (SW2) Push during a power on sequence to boot into the Flash-N-Go. 6.14 Power LED (D30) Should be green when the device is powered up.
PRODUCT MANUAL SANTINO Battery Battery Specifications The internal baseboard is equipped with a Primary Lithium battery (type CR1220), which has a typical lifetime of 8 years. Type SECO Northern Europe Article Number Battery type CR1220 010-0059R Manufacturer Model Camelion CR1220...
PRODUCT MANUAL SANTINO Replacement of the Internal Battery The internal battery is placed as per figure below. For replacement, the SD-card and the back cover have to be removed. The device shall be opened by authorized and skilled personnel only. Danger of electric hazard! First before opening, please make sure that the unit is completely disconnected from any power supply, direct or indirect.
PRODUCT MANUAL SANTINO Annex B: Hardware Revision Information This document is applicable for all products listed below. Please note that customized variants might possibly not support all features listed herein. Additional features are documented in specific attachments. Platform Article Number Marking on PCB SANTINO x1 7.0 OF PCT 900-3537R...
PRODUCT MANUAL SANTINO Annex C: Assembly Options Wi-Fi / Bluetooth Some appliances require a wireless network connection. To be more flexible with regard to future Wi-Fi standards and regulations, we decided not to assemble this functionality directly onto the single-board-computer. We recommend an external USB or miniPCIe solution. Drivers for both versions will be included in the related operating systems.
Supplier Declaration – Directive EG 1907/2006 REACH SECO Northern Europe is manufacturer of electronic products, thus - in the sense of REACH - we are so called „downstream users“. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance.
These solutions are offered exclusively as OEM products. They do not include any application software that is intended for the end user. Therefore, we do not make any EU declarations of conformity in the name of SECO Northern Europe GmbH and do not provide the products with the CE mark.
If the product has been returned with or without prior notice and no failure or malfunction can be detected or the failure or malfunction is caused by inappropriate handling or the device has been returned after expiry of warranty period, SECO Northern Europe reserve the right to charge the user for repair or replacement.
If you intend to use these products in applications as quoted in (II) we highly recommend a personal contact with our consultants and/or technical sales team. (I) Recommended application areas for SECO Northern Europe embedded systems Even for these applications, we recommend to get in contact with our technical sales team. We offer a wide range of support, even at an early stage of evaluation and/or design-in phase.
SANTINO Annex F: Technical Support Before contacting the SECO Northern Europe support team, please try to help yourself by the means of this manual or any other documentation provided by SECO Northern Europe or the related websites. If this does not help at all, please feel free to contact us.