Seneca R-KEY-LT Installation Manual
  1. Manuals
  2. Brands
  3. Seneca Manuals
  4. Gateway
  5. R-KEY-LT
  6. Installation manual

Seneca R-KEY-LT Installation Manual

Hide thumbs Also See for R-KEY-LT:
1
2
3
4
Table of Contents

Advertisement

Quick Links

Download this manual
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol
The word ATTENTION preceded by the symbol
instrument or the connected equipment. The warranty shall become null and void in the event of improper use or
tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if
the instructions contained in this manual are not followed.
WARNING: The full content of this manual must be read before any operation. The module must only be used by
qualified electricians. Specific documentation is available via QR-CODE shown on page 1.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre
authorized to recycle electrical and electronic waste.
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287
CONTACT INFORMATION
Technical support
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modified or supplemented for technical and/or sales purposes.
MI00472-3-EN
INSTALLATION MANUAL
R-KEY-LT
R-KEY-LT-P
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to
electrostatic discharges. Take appropriate measures during any operation.
DOCUMENTATION
R-KEY-LT
support@seneca.it
INSTALLATION MANUAL
indicates conditions or actions that put the user's safety at risk.
indicates conditions or actions that might damage the
DOCUMENTATION
R-KEY-LT-P
Product information
sales@seneca.it
1/4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R-KEY-LT and is the answer not in the manual?

Questions and answers

Related Manuals for Seneca R-KEY-LT

Summary of Contents for Seneca R-KEY-LT

  • Page 1 The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste. DOCUMENTATION DOCUMENTATION R-KEY-LT R-KEY-LT-P SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287 CONTACT INFORMATION Technical support support@seneca.it Product information sales@seneca.it This document is the property of SENECA srl.
  • Page 2 Flashing Packet transit on Ethernet port ETH LNK (Green) Flashing Ethernet port connected Flashing Profinet communication active (R-KEY-LT-P version only) No Profinet communication COM+PWR Flashing Webserver active / Profinet not active (R-KEY-LT-P version only) DEVICE CONFIGURATION The device can be fully set up via integrated web server. The product programming and/or configuration tools, as well as all the manuals, can be downloaded using the QR-CODE from the web address: For further information, refer to the USER MANUAL.
  • Page 3 The device is normally in Profinet mode; in Profinet mode the device can be configured only through the Easy Setup 2 software. In order to access the internal webserver it is necessary to put the device in Webserver mode using the Easy Setup2 or Seneca Device Discovery software.
  • Page 4 DIP switch selectors must be set to OFF To reset the device to factory settings both SW1 DIP switches must be set to ON To force the device’s IP address to the standard value of SENECA Ethernet products: 192.168.90.101 Reserved ELECTRICAL CONNECTIONS CAUTION Switch the module off before connecting inputs and outputs.

This manual is also suitable for:

R-key-lt-p

Table of Contents