Download Print this page

CATSKILL 1448 Assembly Instructions Manual

Hide thumbs Also See for 1448:

Advertisement

Quick Links

A. Assembly uses the Bastion System; a simple yet rugged compression
fastening system.
B. This unit is made of solid North American hardwood and has a factory
applied oil finish. See the enclosed booklet for care instructions.
C. Directions (left/right, front/back) are given as facing the front of an
assembled unit.
C R A F T S M E N ,
Assembly Instructions
Model 1448
Model 1448
I N C .

Advertisement

loading
Need help?

Need help?

Do you have a question about the 1448 and is the answer not in the manual?

Questions and answers

Summary of Contents for CATSKILL 1448

  • Page 1 C R A F T S M E N , I N C . Assembly Instructions Model 1448 A. Assembly uses the Bastion System; a simple yet rugged compression fastening system. B. This unit is made of solid North American hardwood and has a factory applied oil finish.
  • Page 2 Model 1448 Parts List P/N: FL/BRleg1448B (2) Front Left/Back Right Legs 33-1/2” x 2-3/16” x 2-3/16” P/N: FR/BLleg1448B (2) Front Right/Back Left Legs 33-1/2” x 2-3/16” x 2-3/16” P/N: TT1448B (1) Table Top 48” x 24” x 2” P/N: TBK1448B (1) Top Back Brace 39-1/2”...
  • Page 3 Model 1448 Parts List Continued (12) (14) P/N: L-bracket1448B (4) L-Brackets P/N: SKRU 7/16 panhead (8) P/N: SKRU 5/8 #6 (8) 7/16 #6 PANHEAD SCREW 5/8 #6 WOOD SCREW P/N: Pipe1448B P/N: EndCap1448B (1) Nickel Plated Towel Bar Handle (2) Pipe End Cap 32”...
  • Page 4 INSTRUCTIONS FOR BASTIONS ILLUSTRATION ONLY. See Steps 1 & 3 for bastion placement for this unit. Bastion Assembly...
  • Page 5 STEP 1 Table top “L” Bracket holes ASSEMBLE SIDE PANELS nut access holes not used A. Each side panel consists of two (2) legs, one (1) top side brace and one (1) glide support brace. When assembled, TOP SIDE BRACE diagonal legs will be the same (i.e.
  • Page 6 7/16” PREPARE SIDE ASSEMBLIES FOR BACK Bastion Post Positions for BRACES Top Back Brace inch The Top Back Brace utilizes the Bastion system for attachment. Place the Bastion posts into their positions on the back legs only of both side assemblies.
  • Page 7 STEP 3 ATTACH BACK BRACE A. You may find it easiest to attach the back brace and shelves by inverting the island. Attach the back brace with bastions to the right and left side assembly. STEP 4 ATTACH SHELVES A. It is recommeded to get a friend to help hold the shelves in place as you attach them using 1-1/4” #8 screws.
  • Page 8 STEP 5 TABLE TOP PREPARATION & ATTACHING Attach four (4) “L” brackets (using 5/8” #6 screws) to the bottom side of the table top. Note the proper position of the “L” brackets. Illustration 7-A Make sure the round hole is used to attach the L-Bracket to the STEP 6 bottom of the Table Top.
  • Page 9 STEP 7 INSERT LEVELER FEET A. Hammer the threaded T-bolt into the predrilled hole on the bottom of each leg. Screw the leveler into the T-bolt. Height of each of four levelers can be adjusted to stablize entire unit.
  • Page 10 STEP 8 Assemble Drawers A. Attach the Drawer Back to the Left and Right Drawer Sides with four 1 ¼”#8 Screws. Make sure the slots that run the length of the Sides are aligned with the slot in the Drawer Back to accept the Drawer Bottom.
  • Page 11 C. Take two (2) Bastion Posts, align the threaded Illustration 8C ends of the Posts with the post holes located near the Drawer Front ends of the inside Drawer Front. Tighten Posts down until the solid shaft of the Post hits the wood. Back Post out until the hole/screwdriver slot in the end of the Post is parallel and in direct line with the long edges of the Drawer Front.
  • Page 12 STEP 9 ATTACH TOWEL BAR See Illustrations 10 and 11. Screw Nickel Plated Towel Bar Posts into the drawer front using 1-1/4” #8 screws. Attach pipe holder by sliding supports over posts and secure with tiny set screws using allen wrench provided. Set screws go toward bottom of draw.
  • Page 13 STEP 10 INSERT DRAWER A. Align the drawer glides attached to the drawer and the other half of the glides attached to the glide support braces. Slide the drawer all the way in until you hear an audible click. The drawer should now be secured to the glides.
  • Page 14 Catskill Craftsmen, Inc. STATE _________________________ ZIP _______ 15 West End Ave. Please make checks payable to: Catskill Craftsmen Inc. 15 West End Ave. Stamford, NY 12167-1296 Stamford, NY 12167-1296 C R A F T S M E N , I N C .