Related Manuals for MTX PROXP-20-SW
Summary of Contents for MTX PROXP-20-SW
- Page 1 PROXP-20-SW POLARIS PRO XP SUBWOOFER ENCLOSURE ® ® OWNER’S MANUAL M T X . C O M...
-
Page 2: We're Here To Help
MTX! WE’RE HERE TO HELP We’re here to help with any installation or technical support. Visit mtx.com to chat, call 1-800-225-5689 to speak with an MTX Technical Support representative, or visit youtube.com/user/MTXAudioUSA to view product videos. -
Page 3: Specifications
FEATURES • Ported Enclosure Design Produces Louder, Deeper Bass Output • Includes an MTX 55 Series Subwoofer for its Deep Bass Reproduction Capabilities • Compatible with Existing OEM Front Speaker Enclosures • Mounts Behind Dashboard • Factory Matched Texture • Installer Friendly Design •... - Page 4 DISASSEMBLY Step 1 - Start by removing the hood. Remove two (2) T-40 TORX bolts and lift off. Step 2 - Remove two (2) T-40 TORX bolts located under hood securing the front of the dash. Step 3 - Remove two (2) panel clips located under the hood securing the left and right fenders. M T X .
- Page 5 Step 4 - Remove three (3) grey trim pieces from the front of the dash using a panel removal tool or by gently prying with a flat blade screwdriver. One left of steering wheel One right of steering wheel One on passenger side M T X .
- Page 6 Step 5 - Remove seven (7) T-40 TORX bolts across the bottom front and top of the dash panel as indicated. M T X . C O M...
- Page 7 Step 6 - Remove four (4) T-20 TORX screws found under the passenger side glove box lid. This will allow the glove box to drop out from the bottom of the dash. Note: This pocket will not be reused with the subwoofer enclosure installation.
- Page 8 Step 8 - Disengage the tweeter housing from the top of the dash panel and slide up the cage. Step 9 - Starting on either side, lift on the fender panel to disengage the tabs that pass through the dash panel. While lifting, slide the dash panel toward the back of the vehicle freeing it from the fender.
- Page 9 Step 10 - Locate and remove the under-dash tray found below the center storage pocket location by removing five (5) panel clips and two (2) T-25 TORX screws located on the firewall below the pulse connector bank. If the vehicle has the OE audio amplifier installed, disengage its harness connector, and lift the panel out.
- Page 10 Note: If you are installing the subwoofer enclosure as part on an MTX Thunder kit, this tray will not be reused. The kit amplifier mounting rack will replace this part. If not installing as part of an MTX Thunder kit, the tray will need to be modified as indicated prior to reinstallation. Cut and remove the area indicated.
-
Page 11: Installation
Step 12 - Locate the subwoofer mounting bracket, three (3) 10mm bolts and two (2) t-40 TORX bolts. Step 13 - Holding the subwoofer enclosure with the MTX logo up and the woofer facing the passenger seat, install the enclosure from below by lifting and rotating the enclosure into place. The padded channel on the top of the enclosure will seat below the frame tube at the top of the dash. - Page 12 Step 14 - Holding the enclosure in place, install the upper bracket in place by sliding the slots over the molded tabs at the front of the enclosure lining up the three holes with the brass inserts in the top of the enclosure.
- Page 13 Note: If installing as part of an MTX Thunder kit, plug the subwoofer enclosure into the subwoofer harness provided in the kit. If not installing as part of an MTX Thunder kit, the enclosure will need to be hardwired by removing the connector and following the wiring diagram below.
- Page 14 Once the subwoofer enclosure is connected test for function. Step 19 - Reassemble and go ride. M T X . C O M...
-
Page 15: Warranty Period
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. - Page 16 Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice.