Advertisement
RPK4-HD1101
RPK4-HD1101 Settings Menu (cont.)
P3. - Steering Wheel Control Re-calibration.
SWC re-calibration is necessary when the SWC operation is erratic or non-existent. This process re-calibrates the SWC values to the RPK4
in the table below. If your vehicle is not equipped with the Voice and Back navigation buttons you will end programming by waiting 7 seconds
for the module to time out after the Mode button has been programmed. The SWC and radio command assignments can always be restored to
default values by entering re-calibration mode (Steps 1-3) and not pressing any buttons. After 7 seconds the re-calibration mode will time out and
all default values will be restored.
1.
Start with the Ignition in the OFF position.
2.
Press and hold the Auto
3.
While holding the button down turn the key to the ignition position and continue to hold for 7 seconds or
until "P3" is shown on the display. At this point the recirculation amber LED will turn on solid.
4.
Within 7 seconds, press the button that is to be learned on the steering wheel. The recirculation amber
LED will turn off when the button is pressed. Once the value has been successfully learned the LED will
5.
If you need to program more buttons, repeat step 4 for each additional audio function on the steering wheel.
6.
indicating end of programming.
7.
Test the interface for proper functionality. If any function does not work, repeat the programming steps.
8.
After you have re-calibrated the SWC buttons, the default SWC button assignments will be the same as
what is listed in the chart on page 7. If you wish to re-assign button functions you must also go through
the programming process (P1) on the previous page.
P4. - Temperature unit selection.
1.
Start with the Ignition in the OFF position.
2.
Press and hold the MAX A/C
3.
While holding the button down turn the key to the ignition position and continue to hold for 7 seconds or until "P4" is shown on the display.
4.
This tells you that you are in programming menu 4 along with the current selection on the right of the display which is 1 by default. The
available selections are as follows:
1. Fahrenheit (Default)
2. Celsius
5.
Using the Fan Up
and Fan Down
6.
Once the desired selection is shown, press the rear defrost button
P5. - Driver Position Selection
This selection needs to be set to right hand drive as it lets the kit know which side of the vehicle the driver is on. This also changes which of the
temperature knobs has priority. Since the driver side knob should always have priority, we adjust the priority based on your selection.
1.
Start with the Ignition in the OFF position.
2.
Press and hold the A/C
3.
While holding the button down turn the key to the ignition position and continue to hold for 7 seconds or until "P5" is shown on the display.
4.
This tells you that you are in programming menu 5 along with the current selection on the right of the display which is 1 by default. The
available selections are as follows:
1. Left Hand Drive (Default)
2. Right Hand Drive
5.
Using the Fan Up
6.
Once the desired selection is shown, press the rear defrost button
P6. - Temperature Rotary Knob Position Swap
In right hand drive vehicles,this selection also needs to be set to right hand drive. This will make sure that the temperature knob on the right of
the kit controls the right side of the vehicle and the left temperature knob will control the left side. In the event that you select right hand drive in
this menu and the rotary knobs are inverted please change the setting to left hand drive, even if the vehicle is a right hand drive.
1.
Start with the Ignition in the OFF position.
2.
Press and hold the Recirculation
3.
While holding the button down turn the key to the ignition position and continue to hold for 7 seconds or until "P6" is shown on the display.
4.
This tells you that you are in programming menu 6 along with the current selection on the right of the display which is 1 by default. The
available selections are as follows:
1. Left Hand Drive (Default)
2. Right Hand Drive
5.
Using the Fan Up
6.
Once the desired selection is shown, press the rear defrost button
P
ifi A
C
ti
or Temp
button.
button.
buttons change the current selection to match the desired temperature units.
***This Section is for Right Hand Drive Dual Zone vehicles only***
button.
and Fan Down
buttons change the current selection to match the proper driving position.
button.
and Fan Down
buttons change the current selection to match the proper driving position.
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
(next to the
button) to save and exit.
(next to the
(next to the
PAC-audio.com
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2003-2007 Honda Accord
Button Programming Order
Volume Up
Volume Down
Track Up
Track Down
Mode
Voice
Back
button) to save and exit.
button) to save and exit.
Rev: V8
Date: 081318
Page 9
Advertisement
