Advertisement
Quick Links
Advertisement
Related Manuals for Klever Klever Desk Electric Single
Summary of Contents for Klever Klever Desk Electric Single
- Page 1 Klever Desk ® Electric Single Sided Desk Quick Start Guide kleverdesk.co.nz...
- Page 2 Caution Keep children and pets away from the electric high-adjustable desk during the operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for long time. Make sure desktop not touch the wall. Ensure no obstacles in the desk’s path, and no objects above 20”...
- Page 3 Parts Part Name Part Name (PCS) (PCS) Side Bracket ST4.8*16 Tapping Screw Foot ST3.5*16 Tapping Screw Column Control Box Adjustable Frame Handset M6*10 Screw Power Cord M6*16 Screw Extension Cable Cable Clip kleverdesk.co.nz...
-
Page 4: Installation
Installation Step 1: Set frame flat. Unfold columns and ‘click’ in place. Auto Click Unfold when laying down kleverdesk.co.nz... - Page 5 Installation Step 2: Place the side brackets on to the frame. Install the bracket screws and fasten the frames pre-installed screws. M6*10 Screw Fasten the screws Avoid excessive tightening of screws kleverdesk.co.nz...
- Page 6 Installation Step 3: Line up the screw holes on the feet and columns. Fasten the screws. M6*16 Screw Fasten the screws Avoid excessive tightening of screws kleverdesk.co.nz...
- Page 7 Installation Step 4: Check both sides of the desktop before placing the frame on the bottom side of the top. Adjust frame to suitable width (it is suggested that the below measurements are followed when setting the column spacing) and fasten screws. Install the handset in a suitable position underneath desktop edge to avoid interference with humans or chairs, display screen facing out and fasten screws.
- Page 8 Installation Step 5: Install control box on underneath of desktop (see below diagram). Control box must be installed flush and away from desk frame. Handset SMART neo Control Box ST3.5x16 Tapping Screw Step 6: As shown in the below, connect related parts, including control box, handset, extension cable and power cord etc.
- Page 9 Initial Setup Procedure & Manual Reset Risk of minor or moderate injury through crushing. Collision Detection (ISP) is inactive during start-up and reset processes. This may lead to minor or moderate injury through crushing. Ensure that no persons or objects are in the table’s range of motion. NOTICE Operating the table system when it is not properly connected can damage the product.
- Page 10 Adjusting the Table Top Height Risk of minor or moderate injury through crushing Your fingers may be crushed when you attempt to change the height of the table. • Keep fingers away from moving parts • Ensure that no persons or objects are in the table’s range of motion INFO The Table Top will move up or down until the UP or DOWN Key is released, or if a predefined stopping point has been reached.
-
Page 11: Factory Reset
Adjusting the Table to a Memory Position Press and hold the required Memory Position Key (e.g. 2). > The Table Top will move until the saved Table Top height has been reached. If you release the Key before the Memory Position is reached, the table will stop. Release the Memory Position Key >... - Page 12 Container and Shelf Stop Positions These features can limit the movement area of the Table Top (if e.g. a container is below the table or a shelf is above it). Container Stop Positions become the new lowest end position, Shelf Stop Positions the highest. INFO Container Stop Positions can only be saved only in the lower half of the movement area, Shelf Stop Positions in the upper half.
-
Page 13: Error Messages On Display
The display shows an shown. error number. Code Message Required Actions Disconnect the Control Box from the Mains. Contact KLEVER for Internal Error Channel 1 further information. Disconnect the Control Box from the Mains. Contact KLEVER for Internal Error Channel 2 further information. - Page 14 NOTICE Do not operate the table system if problems persist. Contact KLEVER for further information. NOTICE The Middle Switch is only fitted to certain versions of the SMARTneo-2G. Contact KLEVER if you are unsure which version you have. kleverdesk.co.nz...
-
Page 15: Maintenance
Intelligent System Protection Intelligent System Protection (ISP) is KLEVER’s collision detection system. It aims to reduce the risk of system damage when using KLEVER products. When a collision is detected, all Actuators stop immediately and move back in the opposite direction for a few seconds (see 11.2.2 Drive Back Function). The SMARTneo-2G features integrated collision detection via the Light Barrier function. - Page 16 kleverdesk.co.nz...
Need help?
Do you have a question about the Klever Desk Electric Single and is the answer not in the manual?
Questions and answers