Package Contents - DeWalt DW872 Original Instructions Manual

Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
• The plug fitted should be comply with BS EN 60309 (BS4343),
16 Amps, earthing contact position 4h.

WARNING: Always ensure that the cable clamp is
correctly and securely fitted to the sheath of the cable.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Toothed Chopsaw
1 Cutting blade
1 Hex key
1 Vertical clamp
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code 26 , which also includes the year of manufacture,
is printed into the housing.
Example:
2020 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
On/off switch
1
Main handle
2
Carrying handle
3
Guard
4
Spindle lock
5
Material clamp
6
Fence
7
Mounting holes
8
Cutting table
9
Hex key
10
Intended Use
Your professional D
for the cutting of variously shaped metal materials: water
and gas pipes, angular iron, U-profiles, T-bars, rods, bolts, etc.
Using the appropriate cutting blade, it can cut hot and cold
rolled carbon steel, construction steels according to DIN 1700
(ST33, ST37–2, ST52–3), non-ferrous metals (i.e. aluminum,
; the
2
brass, copper), stainless steel and synthetic materials (i.e. PVC).
This tool is not intended to be used in cast-iron, brick, tile or
ceramic materials. The tool is never to be used for cutting
magnesium workpieces
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These chopsaws are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (includng
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Bench Mounting (Fig. A)
Mounting holes
bench mounting.
Removing and Fitting a Cutting Blade
(Fig. A, B1, B2)
1. With the arm in the rest position, use the lip
guard back. Leave the guard retracted (Fig. B1).
4
2. Press and hold down the spindle lock
3. Rotate the cutting blade until it locks.
4. Rotate the bolt cover
5. Using the hex key
counterclockwise and then remove the lock washer
flat washer
6. Replace the cutting blade
new blade is placed onto the flange
rotational direction.
7. Secure the blade with the retaining flange
washer 27
WALT toothed chopsaw has been designed
e
have been provided to facilitate
8
5
11 out of the way (Fig. B1).
10 , remove the bolt
and the retaining flange
27
13 . Make sure that the the
30
and lock washer 29 and the bolt
English
42 to slide the
(Fig. B2).
12 by turning
, the
29
(Fig. B2).
28
in correct
28 , the flat
12 .
9