Safety Technology International STI-6400 Installation

PRE INSTALLATION CHECKLIST
IMPORTANT NOTICE: If you have purchased a STI-6400/WIR model, before installation you will need
to 'learn' the transmitter to the 8 channel receiver. Please refer to the Quick Setup Guide. Once'learned',
follow steps 1-7 opposite.
DO YOU WANT HIGH OR LOW SOUNDER OUTPUT?
The Exit Stopper is factory set for HIGH sounder output (105 dB). To change the unit to a LOW output
(95 dB), locate JP2 and move to the OFF position.
DO YOU WANT THE EXIT STOPPER TO ALARM IMMEDIATELY?
The Exit Stopper is factory set to arm immediately after the key is turned to the ON position. You can
change this to a 15 second arming delay. This feature allows an authorised key holder to turn the unit
on and then exit through the door before the unit arms. To set a 15 second arming delay move jumper
JP7 to the OFF position.
DO YOU WANT THE EXIT STOPPER TO ACTIVATE IMMEDIATELY THE DOOR IS OPENED?
The Exit Stopper is factory set to activate immediately the protected door is opened. The unit can be
set for a 15 second delay. This would allow an authorised key holder to open the door and turn the Exit
Stopper off before it activates. To set to a 15 second activation delay move the jumper to JP5 to the ON
position.
SOUNDER OUTPUT OPTIONS
The Exit Stopper is factory set to sound for 30 seconds once activated. There are three other settings,
180 seconds, continuous and 5 beeps.
SPECIFICATIONS
Housing 3mm 1/8" polycarbonate
Power Source 9 VDC Alkaline
Sounder Output 95 dB - low/ 1 05 dB - high
Relay Output 9 VDC, 40mA
Dimensions 136mm/5.35" h x 136mm/5.35" w x 50mm/1.97" d
Standby Current 10uA
Alarm Current 200mA
EXIT STOPPER PART NUMBERS
PART No. DESCRIPTION
STI-6400 Exit Stopper
STI-6402 Exit Stopper Double Door
STI-6400/RK Remote Kit
STI-6400/RS Remote Sounder
Safety Technology International
Taylor House, 34 Sherwood Road, Bromsgrove
Worcestershire, B60 3DR, England
Telephone: +44 (0) 1527 520 999
Fax: +44 (0) 1527 501 999
E mail: info@sti-europe.com Web Site: www.sti-europe.com
ID6400-6400WIR · Revised 10/16-001 · Printed in England
Need help? Call our Technical Support Team on +44 (0)1527 520 999
ACCESSORIES
PART No. DESCRIPTION
Tamperproof Tool
STI F021
STI CO23/A Spare Keys
STI BAT1 9 V Battery
STI L6400 Emergency Exit Warning Sign
EXIT STOPPER
A completely self-contained security system that provides a highly effective, extremely versatile and
inexpensive way to help prevent unauthorised use of fire/emergency doors. The EXIT STOPPER is
supplied with an installation kit and 9v alkaline battery. It also incorporates a key override facility for
authorised use.
INSTALLATION DATA FOR THE STI-6400 & STI-6400/WIR
1. Make sure key switch is in the OFF
position.
2. Remove cover from base unit by
applying pressure to the key barrel.
Ensure that the tamper screw located
on the bottom right hand side is removed
by using the tamperproof tool provided.
3. Set switches, on circuit board, to desired
alarm settings (figure 4 see over).
4. Mount base unit on or next to door using
the 2 fixings provided. (See Dia. A for
recommendation*). Reed switch mounting
locations can be moved to the four positions
shown in Dia. A. If mounted next to door,
route reed switch wire through knockout in
bottom of housing as shown in figure 2.
5. Mount magnet on door frame (or door if
unit is mounted next to door) using screws
provided. When mounting on metal doors
or door frames, use plastic spacer provided.
Reed switch and magnet must be within
13mm/1/2" when door is closed. Please refer
to figures 5, 6 and 7 for other mounting options.
6. To fix the cover to the base unit, hooks
can be found on the inside top edge of the
cover. Insert the hooks into the slots provided
on the edge of the base unit (see Dia. B) and
snap the cover down until it clicks into place.
Using the tamperproof tool provided insert
and tighten the screw to secure the cover to
the base (see Dia. C).
7. REMOVING THE COVER FROM THE BASE
Remove the tamper screw located on the bottom
right hand side with the tamperproof tool provided.
Apply pressure to the key barrel. Keep the
tamperproof tool safe for future servicing and
battery change.
Need help? Call our Technical Support Team on +44 (0)1527 520 999
FIGURE 1
USING BACK PLATE AS
SHOWN IN FACTORY
REED SWITCH
TEMPLATE MARK AND DRILL
INSTALLED POSITION
(2) 4.7 mm [3/16 in] DIA. HOLES
PC BOARD REED SWITCH MOUNTING
PEGS. (4 OPTIONAL POSITIONS)
RAWL PLUG
9 VOLT
(2) PROVIDED
ALKALINE
BATTERY
KEY SWITCH
SCREW #8 x 1 in.
(2) PROVIDED
OUTER COVER
NOTE: TO SELECT ALARM OPTIONS,
REMOVE OUTER COVER AND FOLLOWING
THE SWITCH SETTINGS CHART, SHOWN ON
REVERSE SIDE, CHOOSE THE ALARM
OPTIONS SUITABLE FOR EACH INSTALLATION.
FIGURE 2
REMOVE FRONT COVER
AND ROUTE REED SWITCH
WIRES THROUGH NOTCH O N
BOTTOM SURFACE AS
SHOWN
13mm [1/2 in.]
MAXIMUM GA P
SPACER S
NOTE: 2 SPACERS UNDER BOTH
SCREW
MAGNET AND REED SWITCH
6 x 1 1/4 in.
MUST BE USED ON STEEL DOORS
(2) PROVIDED
MAGNET
VIEW SHOWING MAGNET INSTALLATION
NB: FITTING UNIT AWAY FROM DOOR (OPTIONAL)
FIGURE 3
DIA. B
HOOK
SLOT
VIEW SHOWING HOW TO FIX THE COVER TO THE BASE
DIA. A
SLOT SLOT
*
4 FIXING HOLES
*
*recommendation
for the fixings
KEY
(2) PROVIDED
(USED AS NECESSARY)
DIA. C
SCREW
TAMPER-PROOF
(1) PROVIDED
TAMPER
PROOF TOOL
(1) PROVIDED