Basic Functions - Maxwell MW-4002 Manual Instruction

ENGLISH

BASIC FUNCTIONS

Adjusting volume level
Use the VOLUME (9) control to adjust the desired
volume level.
Radio stations reception
1. Set the FUNCTION (8) switch to the RADIO po-
sition.
2. Select the desired band: AM, FM, FM ST, set-
ting the (18) BAND switch to the correspond-
ing position.
3. Rotate the TUNING knob (17) to select the de-
sired radio station.
4. After you stop listening to the radio, set the
FUNCTION switch (8) to the OFF position.
Note:
- When tuning to the station, which transmits ste-
reo signal, the FM ST indicator (5), which is situ-
ated on the radio tuning scale, will light up.
- in conditions of bad receipt interferences can
appear (the indicator (5) will be flashing), in this
case set the (18) BAND switch to the FM position,
sound will be played back in the mono mode, but
the interferences level will significantly decrease.
Antenna
- For the best FM reception, completely extend
the antenna (3) and direct it at the desired angle.
- For the best AM reception, try different variants
of the unit orientation in the horizontal plane.
Playback of CD discs
Setting a disc – open the disc compartment lid
(2). Inset a CD disc with a label up and close the
lid (2) of the disc compartment.
Ejecting a disc – after the playback stops open the
CD compartment lid (2), "OP" will appear on the dis-
play (14) and eject the disc. Put the disc in the case.
Always close the CD compartment lid (2) in order
to prevent it from dust. Always eject a disc from the
CD compartment if it is not being played back.
1. Plug in the unit.
2. Select the CD playback mode. To do it, set the
FUNCTION switch (8) to the CD position, the
display lighting (6) will light up.
3. Open the lid (2) insert a disc with the label up
and close the lid (2).
4. After reading of the information from a disc to-
tal number of tracks will appear on the display
(14) and payback of the first track on the disc
will start.
4002IM.indd 6 4002IM.indd 6
Note:
- the unit can playback CD-R and CD-RW discs
- when there is no disc in the compartment or the
disc is damaged "no" will appear on the display
(14).
Playback
- In the stop mode press the button (15), playback
of the disc will start and the number of the played
back track and the
display (14).
Pause
- To pause the playback press the button (15), the
and the number of the track will be flashing on
the display (14).
- To resume the playback, press the button (15)
once again.
Stop the playback
- To stop the playback press the button (13) , to-
tal number of the tracks on the disc will appear on
the display (14).
Moving to the beginning of the previous track
or to the next track.
- During the playback or in the pause mode, to
move to the previous or the next track press the
buttons (11) / .
Moving to the playback of a certain fragment
of a track
- In the playback mode press and hold the buttons
(11) / for quick moving to the playback of a
certain fragment of a track.
Note:
- in the quick moving to the fragment of a track
mode, when one of the buttons (11)
pressed, the sound is not played back.
Repeated playback of a track or a disc
- To repeat one track press the (16) REP once,
"REP" will appear on the display.
- To repeat all tracks on the disc press the (16)
REP twice, "REP ALL" will appear on the display
(14).
Random playback of the recorded tracks
- To playback all tracks in the random order, press
the (16) REP button three times, "RAND" will ap-
pear on the display (14).
6
symbol will appear on the
/ is
30.05.2011 16:11:36 30.05.2011 16:11:36