1. Manuals
  2. Brands
  3. Summit Manuals
  4. Printer Accessories
  5. Minolta SP-6
  6. Technical document

Summit Minolta SP-6 Technical Document

Toner cartridge
Hide thumbs
1
2
3
4
5
6
Table of Contents

Advertisement

Quick Links

Download this manual
Home
New Arrivals!

Overview

Required Tools

Prepare Work Area

Disassembly Instructions

Cleaning the Waste Chamber

Minolta SP-6 Toner Cartridge
DOC-0229
O
VERVIEW
These instructions cover the recharging of the Minolta SP-6 toner cartridge used in the Epson Action Laser 1000,1500, and
other printers using the Minolta SP-6 Laser Engine.
The SP-6 engine is a 6ppm printer engine that runs at 300 dpi. The toner cartridge is rated for 6000 pages at 5% coverage.
More than 200g will fit into the Toner Supply housing, but the waste chamber will fill up and leak if this is done.
The Drum-101 will work in this cartridge, the gears must be transferred from the old drum to the new.
This cartridge also uses a new method of charging the OPC Drum. Instead of using a Corona Wire or rubber Charge Roller, it
uses what is considered to be a conductive felt strip. This strip can be used up to two times before it fails, to ensure a quality
cartridge- it is recommended that the cartridge be tested before remanufacturing. If the test print shows vertical light grey
streaks - the felt strip is probably bad and the cart should not be remanufactured.
The purpose of this disassembly procedure is to vacuum out toner that will have spilled inside the cartridge during shipping and/
or rough handling, to clean the debris cavity, and to clean and fill the supply chamber with new toner. This disassembly
procedure should also be used to examine the internal parts of the cartridge for possible damage, or wear should the printing of
the cartridge be poor and not correctable by any other means.
The following procedure should be read entirely before proceeding.
R
T
EQUIRED
OOLS
99% Isopropyl Alcohol (FR-8)
Cotton Swabs (CT-100)
Lint Free Cotton Pads (PW-96)
Black Toner 200 Grams
Sealing Strip (Optional, see text) (SS-LXO)
Company Info
Publications
Special Features
Contact Us

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Minolta SP-6 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Summit Minolta SP-6

Summary of Contents for Summit Minolta SP-6

  • Page 1 DOC-0229 VERVIEW These instructions cover the recharging of the Minolta SP-6 toner cartridge used in the Epson Action Laser 1000,1500, and other printers using the Minolta SP-6 Laser Engine. The SP-6 engine is a 6ppm printer engine that runs at 300 dpi. The toner cartridge is rated for 6000 pages at 5% coverage.
  • Page 2 Long Life Drum -Optional Padding powder (DPP-K) Wiper Blade (WB-SP6) -Optional Drum Cover (DC-SP6) -Optional EQUIRED UPPLIES Phillips head screw driver. Small Common screw driver Needle Nose Pliers Safety goggles and breathing mask. Vacuum approved for toner Small wire cutters (Optional, see text) Soldering Iron 35 Watt (Optional, see text) WARNING: Always wear safety goggles and breathing mask when working with or around toner.
  • Page 3 6. Carefully remove the OPC drum, being very careful not to scratch it. Vacuum any remaining toner and debris from the drum, being very careful not to come into contact with the drum surface. Do not polish or wipe the drum with a dry cloth, since this may scratch the drum.
  • Page 4 2. Pry the Recovery Blade Assembly off the Waste Chamber. It may be necessary to clip off the top of the plastic retaining posts in order to remove it. 3. Vacuum the entire Waste Chamber clean, be careful not to lose the small gear on the right side of the cartridge. 4.
  • Page 5 clean compressed air. 3. Laser Glass: In the top lid of the printer, behind the hinged protective cover is the protective laser glass. This glass should be periodically cleaned with a clean soft lint free cloth. If this glass becomes dirty, all of the pages printed will be light in the areas of the dirt.
  • Page 6 blade, guided into the waste chamber by the recovery blade, and stored in the waste chamber. The OPC Drum now ready to be Conditioned by the Primary Charge felt, and start the print cycle again. ECOMMENDED UPPLIES Microsoft OLE DB Provider for ODBC Drivers error '80004005' [Microsoft][ODBC Microsoft Access Driver]General error Unable to open registry key 'Temporary (volatile) Jet DSN for process 0x3c30 Thread 0x3e7c DBC 0x840f024 Jet'.

Table of Contents