Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Summit Manuals
  4. Printer Accessories
  5. BROTHER HL-630 OPC
  6. User manual

Summit BROTHER HL-630 OPC User Manual

Summit printer accessories user manual
Hide thumbs

Advertisement

Quick Links

Download this manual
Cartridge/Machine Reset Guide
Now with HP & Lexmark common chip error codes!
th
Welcome to the 16
version of our Reset Guide!
This guide continues to expand (sometimes on a
daily basis), and it will continue to expand for the
for-seeable future. Although most machines these
days are chip based, some still use the machine
menu to reset the counter. As for the chip based
machines, it basically comes down to if the chip
stops that cartridge from printing or allows the
cartridge to print but disables the toner low circuitry.
We have tried to include this information where ever
possible.
New in this version, we have also included
common chip error codes and their explanations.
Sometimes what is perceived to be a chip error can
be something else. Codes for HP and Lexmark
machines have been included. Rather than copy
them for every HP and Lexmark engine, we have
included a generic listing at the beginning of both
the HP and Lexmark section. Only if there is a
specific machine error code will there be anything
under the actual engine.
If you have information not listed here, please
contact Mike Josiah at
mjosiah@summitechnologies.com so it can be
included in the next version.
Brother HL-630 OPC
Brother Cartridge
Part #DR-100
OEM Stated Yield: 11-15,000
This cartridge does not use any type of reset
procedure. These cartridges according to the Brother
manual should be replaced whenever the copy
quality deteriorates. Since this could occur almost at
any time, there is no need to have a counter. We only
included it here because all of the other Brother
engines DO have some sort of reset procedure.
MM
SU
IT Technologies
By Mike Josiah
New drum cartridges come with a clear "Starter
Sheet" installed inside the cartridge. When the
cartridge is installed and the cover closed, the printer
will eject the sheet and at the same time, reset the
drum counter. This sheet is also present in the DR-
300 cartridges. Replacement sheets are now
available.
Brother Intellifax 2800/2900/3800
(Also used in the DCP-1000/MFC-4800 and
New drum cartridges come with a clear "Starter
Sheet" installed inside the cartridge. Install the
cartridge but keep the cover open. Press the
"CLEAR" button to show the drum status. The
display will show REPLACE DRUM? 1. YES 2. NO
Press "1" on the telephone keypad. The counter is
reset! Replacement sheets are now available.
Version
Brother HL-720 OPC
Brother Cartridge
Part #DR-200
OEM Stated Yield: 20,000
OPC
Brother Cartridge
Part #DR-250
OEM Stated Yield: 20,000
MFC-6800)
16

Advertisement

loading
Need help?

Need help?

Do you have a question about the BROTHER HL-630 OPC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Summit BROTHER HL-630 OPC

Summary of Contents for Summit BROTHER HL-630 OPC

  • Page 1 If you have information not listed here, please contact Mike Josiah at mjosiah@summitechnologies.com so it can be included in the next version. Brother HL-630 OPC Brother Cartridge Part #DR-100 OEM Stated Yield: 11-15,000 This cartridge does not use any type of reset procedure.
  • Page 2 Brother HL-1040 OPC Brother Cartridge Part #DR-300 OEM Stated Yield: 20,000 New drum cartridges come with a clear “Starter Sheet” installed inside the cartridge. When the cartridge is installed and the cover closed, the printer will eject the sheet and at the same time, reset the drum counter.
  • Page 3 Brother HL-3260N OPC Brother Cartridge Part #DR-1200 OEM Stated Yield: 60,000 The HL-3260 is Brothers first high speed printer. The drum cartridge comes with three RED sheets and two pieces of tape installed on the cartridge. There is a possibility that there is developer inside the drum cartridge.
  • Page 4 Brother HL-7050 Toner Brother Cartridge Part #TN-700 (TN-5500) OEM Stated Yield: 12,000 Located inside the cartridge handle is a small fuse that looks similar to a resistor. It is a 1/8A, 250V fast acting fuse, and must be replaced each cycle. Brother HL-7050 OPC Brother Cartridge Part #DR-700 (DR-5500)
  • Page 5 Canon NP-6016/C-160 OPC Canon Cartridge Part # F43-4921-700 (NPG-9) OEM Stated Yield: 40,000 The drum unit for these cartridges is rated for 40,000 pages. The machine will show “Replace Drum” at 40,000 pages or when the waste toner section is full. These cartridges have a reset chip built into the connector.
  • Page 6 for 5% pages, so it is very possible that you have an empty cartridge with a green wheel showing, or a half full cartridge with a red wheel showing. It all depends on how much toner is used per page. To reset the counter, grasp the color wheel in your right hand, the gear assembly in your left.
  • Page 7 Goldstar GL-660 (Xerox W.C. Pro 610) 6R00833 Toner, 13R00532 OPC Toner: 5,000 pages, OPC: 10,000 Pages Toner With the Machine on, open the access cover. Press “MENU”, Press “6”, Press “3” Press “CLEAR”, Press “ENTER” With the Machine on, open the access cover. Press “MENU”, Press “6”, Press “4”...
  • Page 8 HP Color LaserJet 2600 HP Black # Q6000A, Cyan Q6001A, Magenta Q6003A, Yellow Q6002A OEM Stated Toner Yield: 2500 Black, 2000 Color These cartridges have what HP now calls “Smart Print Technology Chips”. These are the latest in HP chips, they are very small, and contain all new code. As with most HP chips, these chips monitor toner usage.
  • Page 9 HP Color LaserJet 3700 HP Black # Q2670A, Cyan Q2681A, Yellow Q2682A, Magenta Q2683A OEM Stated Toner Yield: 6000 Black, 6000 Color These cartridges have what HP now calls “Smart Chips” Similar to other HP chips, these chips monitor toner usage, Internet supplies ordering, and a new feature, remote troubleshooting.
  • Page 10 HP Color LaserJet 4500 Transfer Belt HP OPC Part # C4196A OEM Stated Yield: 100,000 Black, 25,000 Color Press the menu button until “RESET MENU” is displayed. Press the “ITEM” button until “NEW TRANSFER KIT, SELECT IF DONE” is displayed. Press the “SELECT”...
  • Page 11 HP Color LaserJet 5500/5550 HP Black # C9730A, Cyan C9731A, Magenta C9733A, Yellow C9732A OEM Stated Yield: 13,000 Black, 12,000 Color These cartridges have what HP now calls “Smart Chips. Similar to the HP-4100, these chips monitor toner usage, Internet supplies ordering, and a new feature, remote troubleshooting.
  • Page 12 HP LaserJet 1300 HP Part # Q2613A/X OEM Stated Yield: 2,500/4,000 The HP-1300 uses the second generation black toner cartridge ARD’s. These chips (ARD’s) only monitor toner usage not page counts. Each chip also has its own serial number which in effect gives the cartridge a serial number.
  • Page 13 set to YES on the cartridge chip. Even after the cartridge is refilled, the printer display will still show “Toner Low” for the supplies status section of the menu. Since these machines do not have a display, only the supplies status page will show “Non HP Toner cartridge”.
  • Page 14 the menu. The main display will then show “Non HP Toner cartridge”. If the chip is removed, the toner low sensors will be disabled, and will not work again until a new HP cartridge is installed. Replacement chips are available. Specific 4250 Error Codes “10.32.00”...
  • Page 15 HP LaserJet 9000 HP Part # C4583X OEM Stated Yield: 30,000 Like the HP-4100, the 9000 cartridge also uses a chip. The chip in the 9000 is the same as the 4100 in that they only monitor usage not page counts. Each chip also has its own serial number which in effect gives the cartridge a serial number.
  • Page 16 Kyocera F-3010 OPC Kyocera OPC Part # DK-2 OEM Stated Yield: 10,000 There is a small black fuse located on the board inside the cartridge. This fuse must be replaced each cycle by un-soldering the old and soldering in the new.
  • Page 17 Lexmark 4023 (Optra W820/Xerox 4525) Lexmark Cartridge Part # 12B0090 OEM Stated Yield: 5840/5740: 10,000. 5845/5745: 25,000 The “Return” cartridges have an ARD on a small board located inside the right end cap of the cartridge. Unlike other Lexmark chips, the board for these cartridges has two contact pads where the machine makes direct contact.
  • Page 18 E-120 Drum cartridge: With the printer turned on, open the front door. Press and hold the CANCEL button until all the lights begin to cycle. Close the front door. Press the continue button to resume printing. Lexmark E220 Lexmark Cartridge Part 12S0300 (Return Program), 12S0400 (Standard) OEM Stated Yield: 2,500 This system uses a separate toner and drum...
  • Page 19 Lexmark E238 Lexmark Toner Cartridge Part #’s 23800SW, (Return Program), 23820SW (Standard) OEM Toner Stated Yield: 2,000 OEM Drum cartridge 12A8302, Stated drum yield: 30,000 Toner cartridges: The “Return” toner cartridges have an ARD on a small board located inside the right end cap of the cartridge.
  • Page 20 Lexmark E321/323 Lexmark Cartridge Part 12A7400/12A7405 (Prebate), 12A7305 (Non Prebate)) OEM Stated Yield: 3,000 (7400), 6000 (7305) The “Return” cartridges have an ARD on a small board located inside the right end cap of the cartridge. Like other cartridges in this series, the board for these cartridges has two contact pads where the machine makes direct contact.
  • Page 21 Lexmark T620/622 Lexmark Cartridge Part # 12A6760/12A6860 12A6765/12A6865 OEM Stated Yield: 6760/6860 10,000: 6765/6865 20,000 The “Return” cartridges have an ARD installed on the right side of the cartridge, (as the cartridge would be inserted into the machine. These chips are physically located in a different spot from the older Optra T cartridges.
  • Page 22 Lexmark W812 (Fuji-Xerox XP-26) Lexmark Cartridge Part # 14K0050 OEM Stated Yield: 12,000 These cartridges use a chip, but it is not the “Killer type” These chips monitor the “Toner Low” as well as tell the machine the brand of cartridge it is. So far we have seen Lexmark, Epson, and IBM machines using these cartridges.
  • Page 23 Minolta PageWorks 1400 Minolta Toner cartridge Part #9J04203 Minolta Drum Cartridge Part # M4519401 OEM Stated Yield Toner: 2,000 OEM Stated Yield OPC: 20,000 Toner Cartridge: These toner cartridges have a chip that must be replaced each cycle. The chip is located on the bottom left side of the cartridge.
  • Page 24 engine is the Okidata OL-400/800, but the first actual reset procedure is for the OL-800 series only, followed by other machines that use the same engine but have different reset procedures. Just to make things a little crazier, there are also machines that use different engines, but use the same reset procedure.
  • Page 25 Okidata C3000 Series Okidata OPC Color Cartridge Part # 42126661, 42126660, 42126659, 42126658 OEM Stated Yield: 15,000 All These machines have a glass fuse that is used to reset the machine. The fuse is located in the gear end cap of the cartridge. We have not confirmed this yet, but we believe that the fuse is the same as the SF-5100.
  • Page 26 Okidata OL-400e OPC Okidata OPC Cartridge Part # 56116801 OEM Stated Yield: 20,000 (The procedure for these machines is the same as used for the Okidata OL-1200, OP-20) Turn off the printer While holding the MENU1/MENU2 button down, turn the printer back on. Keep holding the button down until you see USER MNT on the display panel.
  • Page 27 Okidata OL-1200 OPC Okidata OPC Cartridge Part # 56118801 OEM Stated Yield: 30,000 (The procedure for these machines is the same as used for the Okidata OL-400e, and OP-20) Turn off the printer While holding the MENU1/MENU2 button down, turn the printer back on. Keep holding the button down until you see USER MNT on the display panel.
  • Page 28 Okidata OP-14e Okidata OPC Cartridge Part #41331601 (Type 8) OEM Stated Yield: 20,000 (The procedure for these machines is the same as used for the Okidata OP-6e, OL-600e, OP-10e) From the computer the printer is directly hooked up to, enter the Printer Status Monitor. Click on the “Printer Menu”...
  • Page 29 Panasonic KXP-4420 Toner/4420 Panasonic cartridge Part #’s KX-P451, KX- PDM2 OEM Stated Yield: 18,000 Both of these cartridges use a simple 1/16 amp fuse that must be soldered in. The OEM fuse looks like a black transistor. Most of the replacement fuses being sold are in a resistor type package.
  • Page 30 will momentarily press in a lever inside the machine and start to reset the counter. The tape will then break releasing the lever finishing the reset procedure. Make sure you use a thin tape and not a packing tape, as it is important that the tape break fairly easily.
  • Page 31 Samsung CLP-600 Toner/OPC Cartridges Samsung Cart. # CLP-K600A, CLP-C600A, CLP-M600A, CLP-Y600A OEM Stated Yield: 4,000 Black, 4,000 Color These cartridges use a chip that must be replaced each cycle. The chip is located on the rear of the waste hopper. There is no known reset method through the printers menu.
  • Page 32 Samsung ML-2150 Toner Cartridges Samsung Cart. # ML-2150D8/XAA OEM Stated Yield: 8,000 These are the first Samsung cartridges to use a chip. The chips can sometimes be used another cycle, but to be safe it is best to replace them each cycle. There are different manufacturers using this engine.
  • Page 33 Samsung SCX-6320Toner/OPC Cartridges Samsung Cart. # SCX-6320D8 (Toner), SCX- 6320R2 (Drum) OEM Stated Yield: 8,000, 18,000 respectively Both of these cartridges use different items to reset the printer. The toner cartridge uses a chip that must be replaced/reset each cycle. There are different manufacturers using this engine.
  • Page 34 pages. These cartridges are designed to be recycled by Sharp authorized dealers. As such, replacement chips are available from authorized Sharp dealers, and now generic chips are also available. Since the chip shuts down the cartridge at 10,000 pages, you can recycle the cartridge 2-3 times with the same chip with out any problems.
  • Page 35 actuator (or flag) is next to the small gear). On some cartridges the "flag gear" is now black. It is located to the bottom right of the white gear. Make sure that when you snap the green end cap back on, the notch on the small gear lines up with the tab on the large single gear that is on the cartridge.
  • Page 36 Sharp AR-152 Developer Sharp Cartridge Part # AR-152DV OEM Stated Yield: 25,000 The developer is rated for 25,000 pages. The default setting on the machine is to keep running even after the 25K pages. That default setting can be set by the dealer to stop at 25K pages.
  • Page 37 Sharp Cartridge Part # AR-201ND OEM Stated Yield: 30,000 The developer is rated for 30,000 pages. The default setting on the machine is to keep running even after the 30K pages. That default setting can be set by the dealer to stop at 30K pages. It is considered a dealer option.
  • Page 38 OEM Stated Yield: 20,000 (All) These cartridges do not use any reset procedures at all. According to the Sharp manual, they should be replaced when the copy quality deteriorates. No codes will show on the display to change the cartridge. NOTE: None of these cartridges are interchangeable, they all are slightly different.
  • Page 39 The display will read PCU DIAG MODE G. Press the MENU key repeatedly until you see COUNTER SET. Press the ENTER key once, and the MENU key twice. The display will read DRM 05000. Press and hold the DOWN ARROW key until the number resets to 00000.
  • Page 40 Turn the power off. Hold down the exposure button, and turn the power on. All the lights except the ready light will come on. Release the exposure button. Press the exposure button again and hold for 10 seconds, until the three exposure lights come on. Release the exposure button.
  • Page 41 TEC LB-1305 OPC OEM Stated Yield: 10,000 (All) There are three major versions of these cartridges. Two use an external counter and one doesn't use one at all. The older style 1305 has no counter. The label on top of the cartridge has a place to write down the starting page count.
  • Page 42 type of replacement cartridge that the machine is expecting. 001=113R180/181, 005 = 113R287. If the cartridges your machine needs is not available, you can change what type of cartridge the machine will accept by doing the following. Enter the diagnostics mode as in above. Enter “406 “ and press Print.
  • Page 43 cartridge is changed. A new fuse is not needed. However if the machine says change cartridge, the fuse is needed. Since you really have no way to know the state of your customer’s machine, we recommend that the fuse be replaced each cycle. These fuses are very inexpensive, and this way you have no worries! Starter cartridges can come with plastic dummy fuses.
  • Page 44 use the correct connector. The 5012 will not work in the 5011 and vice-versa. To tell if you have the correct connector, read the resistance between pin’s 3 & 6. 5011 connectors read 15,000 ohms while 5012 connectors read 1,500 ohm Xerox 5012/5014 OPC 13R19 OEM Stated Yield: 18,000...
  • Page 45 Xerox 5113 Series (5113, 5114, 5614) Xerox Cartridge Part # 113R79 OEM Stated Yield: 18,000 To reset the counter in the 5113 OPC cartridges the connector on the rear of the cartridge must be replaced. This will clear the J7 or J8 codes. J7= change copy cartridge, J8 = wrong or bad connector.
  • Page 46 Xerox 5318/5340 Xerox Cartridge Part # 13R75/13R56 OEM Stated Yield: 25,000 To reset the counter in the 5318 OPC cartridges the connector on the rear of the cartridge must be replaced. This will clear the J7 or J8 codes. J7= change copy cartridge, J8 = wrong or bad connector.