1. Manuals
  2. Brands
  3. Schweigen Manuals
  4. Engine
  5. Isodrive 3200
  6. Installation manual

Schweigen Isodrive 3200 Installation Manual

Hide thumbs Also See for Isodrive 3200:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
Isodrive 3200
www.schweigen.com.au
4.2021 / V3.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Isodrive 3200 and is the answer not in the manual?

Questions and answers

Related Manuals for Schweigen Isodrive 3200

Summary of Contents for Schweigen Isodrive 3200

  • Page 1 INSTALLATION GUIDE Isodrive 3200 www.schweigen.com.au 4.2021 / V3.0...

  • Page 2: Welcome

    Welcome Thank you for purchasing your new Schweigen Isodrive system. To get the maximum output from this unit, please read through this guide before use and installation. This guide contains important information on the correct use and maintenance of the unit, as well as important safety notes.

  • Page 3: Table Of Contents

    5. Flexible Duct ..........................16 Shallow Roof Space....................................17 Securing Flexible Duct ..................................18 6. Measurements ..........................19 Measurements for Isodrive 3200 (Not to Scale) ........................19 7. Parts List ............................20 Parts List for Isodrive 3200 ................................20 8. Maintenance ..........................22 Roof Restoration or Cleaning ................................22 9.

  • Page 4: Your Safety

    Children should be supervised to ensure that they do not play with the appliance, it is not a toy. Do not install Isodrive motor to a non-Schweigen and/or non-silent rangehood. If you fail to do so, your warranty will be voided.

  • Page 5: Your Safety

    See installation instruction notes ‘Why flexi-duct’ . Recommended Installation Distance Isodrive 3200 motor, recommended 4 to 5 metres of flexi ducting. NOTE: Although less than 4 to 5 metres will increase extraction power this may result in a higher air noise level.

  • Page 6: Minimum Mounting Height

    Any installation problem must be reported to Schweigen. Call outs relating to incorrect installation will result in a service fee direct to the customer. Schweigen takes no responsibility for problems caused by faulty installation, this may void warranty. A preferred installer list can be obtained from Schweigen website www.schweigen.com.au or by calling...

  • Page 7: Description

    NOTE For more flexible ducting instructions, refer page 19. Isodrive Motor Included in the box: 1. Isodrive 3200 motor Approx. 3 metre, 10amp cable and standard male plug 2. Fire resistant 250mm OD PVC riser pipe NOTE: Cable cut-out at the both ends 3.

  • Page 8: Installation

    Please be aware that the 3200 motor is capable of expelling air at 3200m /hr. For more information on environmental noise limit and conditions please contact your local Council. We have a list of recommended installers available on the Schweigen website. Page 8...
  • Page 9 4. Installation 4. Installation 3200 motor Power cord 250mm 50mm Pipe protrusion above dektite PVC Pipe Dektite Fix pipe to fan module with side locking screws Fit side supports to locate Strap to supports 250mm flexible duct (minimum 4 metres ducting length fully extended) NOTE: Prevent any...

  • Page 10: Through Wall Installation

    4. Installation Through Wall Installation Minimum protrusion distance from wall Recommended to fix pipe to a 40mm support structure or strapping 70mm (End of pipe) bracket (not included in Connecting pipe mounting kit). Wall ø 250mm Power cable Mounting points Ensure power cable, pipe and cover plate Wall cover plate (Optional - Part Number P2025)
  • Page 11 4. Installation Protrude pipe to distance 70mm (use as reference only) Mounting points Fix pipe to structure or with a strapping bracket. Marked fastening holes first before Install fan installing unit last Ensure slot cover Wall cover plate plate, power cable (Optional - Part Number P2025) and pipe slot is at the bottom.

  • Page 12: Twin 200Mm Outlet Installation Example (3200 Kit Required)

    4. Installation Twin 200mm Outlet Installation Example (3200 kit required) This is for use where one motor is to be used and there are two 200mm outlets. 3200 motor Ensure flexible ducting is fully extended and as short as possible. Use smooth flowing curves for maximum air flow.

  • Page 13: Optional Back Draft Shutter Installation Through Roof

    4. Installation Optional Back Draft Shutter Installation Through Roof • Cut 250mm flexible duct length to approximately 150mm to 200mm. • Assemble by fitting shutter assembly into the ducting. • Check to ensure the flaps close and open freely before assembling the bottom end of the ducting. 3200 motor PVC Storm pipe Cut existing ducting to...

  • Page 14: Optional Back Draft Shutter Installation Through Wall

    4. Installation Optional Back Draft Shutter Installation Through Wall 3200 motor PVC storm pipe Cut existing ducting length to 150mm to 200mm and assemble to the shutter system. Secure with duct tape and clamp. Back draft shutter system Make sure the flaps are vertical Wall cover plate with notch at bottom (optional part) Ensure that power cable passes...

  • Page 15: Optional Weather Shield Installation Guide

    4. Installation Optional Weather Shield Installation Guide Step 1 Remove Weather Shield (1 pc), P1128 Screws (2pcs) and P1128N Nuts (2pcs), Weather Shield Mounting Bracket (5 pcs) and P1124 Hex Head Screws (15pcs) from packaging. Step 2 Remove plastic cover from Weather Shield and bend to form a circle.

  • Page 16: Flexible Duct

    Incorrect installation may reduce airflow or increase noise levels. Call outs relating to incorrect installation will result in a service fee directed to the customer. Schweigen will take no responsibility for problems caused by faulty installation. A list of preferred Schweigen installers can be obtained from the Schweigen website www.schweigen.com.au.

  • Page 17: Shallow Roof Space

    5. Flexible Duct Shallow Roof Space In shallow roof spaces, do not crush or kink flexible ducting, as it will reduce air flow severely. 90 degree curve made of PVC or galvanise can be used as a substitute for the bend, refer to figure 5. 90 degree curve PVC or galvanise curve 250mm flexible ducting...

  • Page 18: Securing Flexible Duct

    5. Flexible Duct Securing Flexible Duct Flexible duct must be installed with supports at maximum intervals of 1.5 metres. Flexible ductwork can be supported by using gaffer or electrical tape. Provided that it does not restrict the internal diameter of the ducting.

  • Page 19: Measurements

    6. Measurements 5. Measurements Measurements for Isodrive 3200 (Not to Scale) Dimensions in mm Isodrive 3200 weighs 8.3 kg without the PVC pipe. 250.5 Figure 3 Page 19...

  • Page 20: Parts List

    7. Parts List Parts List for Isodrive 3200 Figure 8 Page 20...
  • Page 21 7. Parts List Parts List for Isodrive 3200 Number Part Number Description Quantity P1114 Capacitor 4µF P40112 Terminal Box – Box Base and Lid P807 Terminal Block P1101 Fan Top Spinning P2011 M5X8 SUS Hex Nut Cap P2003 Fan Guard...

  • Page 22: Maintenance

    8. Maintenance Roof Restoration or Cleaning Before doing your roof restoration or cleaning, please completely cover the outside motor system and avoid all chemical contact. imporant Any damages caused by the use of chemical products are not covered by warranty. Figure 9 Avoid chemical contact to motor system.

  • Page 23: Warranty / Disclaimer

    All information supplied is to be used for general reference purposes only and is on the understanding that Schweigen Home Appliances will not be liable for any loss, liability or damage of whatever kind arising as a result of any reliance upon such information. All pictures used in the guide are for illustrative purposes only.
  • Page 24 8/3-4 Anzed Court, Mulgrave 3170 Victoria. 1300 881 693 (EST) www.schweigen.com.au...

Table of Contents