Advertisement
Self-cleaning
Only press the self-clean slider when you want to activate the self cleaning
system. Never press the self-clean dial when ironing.
The self-clean function removes scale and impurities. Use the self-clean function once
every two weeks. If the water in your area is very hard, the self clean function should be
used more frequently.
1.
Ensure your iron is switched off and unplugged from the mains supply socket.
2.
Set the steam control
to the no steam position.
r
3.
Fill your iron with water to the MAX level.
4.
Stand your iron on its heel rest, plug in and switch on at the mains supply.
o
5.
Set the temperature control
to the highest (MAX) setting. Allow your iron to
heat up until the temperature indicator light
6.
Unplug your iron and hold it over a sink with the soleplate facing downwards.
Warning: Be careful not to touch the iron's hot surfaces.
7.
Push and hold the steam control slider to the self-clean position
steam will be ejected from the holes in the soleplate along with any impurities.
8.
Slowly rock the iron side-to-side and front to back for 30 seconds. When rocking
the iron, dip the nose of the iron slightly below the rear to make certain the water
circulates completely.
9.
Release the self-clean slider after 30 seconds and pour out the remaining water
out of the fill hole.
10. Rest the iron soleplate horizontally on an old piece of cloth (cotton or towelling is
ideal) to dry.
11. Plug in the iron and turn the temperature control to the
12. When the temperate indicator light turns off, iron an old piece of cloth to allow any
remaining water to escape.
13. Stand your iron on its heel rest and let the iron heat for two minutes to ensure that
the iron is dried out completely.
14. After use, switch off and unplug your iron from the mains supply and allow it to fully
cool before storing.
Cleaning the steam holes
To remove any build-up in or around the steam holes which may affect steam
performance, use a cotton wool tip moistened with methylated spirits. Wipe off the
methylated spirits with a damp cloth then dry the soleplate.
Cleaning the exterior of your iron
To clean the exterior of your iron, wipe it with a soft damp cloth and wipe dry.
Storing
Warning: Allow your iron to completely cool before storing. Always store your iron
on its heel rest. Do not store your iron resting on its soleplate.
The SAFE-STORE™ heat indicator shows you when the soleplate of your iron has
cooled sufficiently for it to be safe to store. If the strip is red, your iron is too hot. When
the words SAFE-STORE appear on the strip against a solid black background, the
soleplate is at a safe temperature for storing.
Never wrap the power cord around the soleplate. The cord can be neatly wrapped
around the heel of your iron.
6
VIN412_VIN413_20EM2 (UK).indd 6-7
turns off.
i
. Hot water and
r
setting.
lll
After sales service and replacement parts
In the case the appliance does not operate but is under warranty, return the product
to the place it was purchased for a replacement. Please be aware that a valid form of
proof of purchase will be required. For additional support, please contact our Consumer
Service Department at 0800 028 7154 or email:
BrevilleEurope@newellco.com.
Troubleshooting
For troubleshooting and FAQs visit www.breville.co.uk/faqs.
Electrical safety
This appliance must be earthed.
This appliance is fitted with either a moulded or rewirable BS1363, 13 amp plug. The
fuse should be ASTA approved to BS1362. If the fuse in a moulded plug needs to be
changed, the fuse cover must be refitted. The appliance must not be used without the
fuse cover fitted.
If the plug is unsuitable, it should
be dismantled and removed from
the supply cord and an appropriate
plug fitted as detailed below. If
you remove the plug it must not
be connected to a 13 amp socket
and the plug must be disposed of
immediately.
If any other plug is used, a 13 amp
fuse must be fitted either in the plug
or adaptor or at the distributor board.
Waste disposal
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. E-mail us at BrevilleEurope@newellco.com for
further recycling and WEEE information.
13A
7
11/23/20 3:53 PM
Advertisement
