Page 1
User Manual AIIS-5410P Power over Ethernet Control System...
Page 2
English user manual included as a PDF file on the CD. Please disregard the Chinese hard copy user manual if the product is not to be sold and/or installed in China. AIIS-5410P User Manual...
Page 3
The documentation and the software included with this product are copyrighted 2016 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice.
Page 4
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
Page 5
Technical Support and Assistance Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: –...
Page 6
RESTRICTED ACCESS AREA: The equipment should only be installed in a Restricted Access Area. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. AIIS-5410P User Manual...
Page 7
5410P- i7-6822EQ 1 DC9~36V U0A1E AIIS- 5410P- i5-6442EQ 1 DC9~36V S9A1E Note! AIIS-5410P supports one expansion slot space and default is PCIe x8. It also supports PCI; you can find a riser card in the accessory box. AIIS-5410P User Manual...
Page 8
32-channel D I/O cable (1 M) for wiring terminal ADAM-3937-BE 32-channel DI/O DB-37 wiring terminal, DIN-rail mount Supports i-Door module (MOS series), except PoE Please refer to Advantech website below or search "iDoor Module i-Door Module Mini PCIe Expansion Kit". (MOS series module) http://www.advantech.com.tw/products/idoor-module-mini-pcie-...
Page 11
Appendix B Programming the GPIO .....73 Supported GPIO Register ............... 74 B.1.1 GPIO Registers................74 B.1.2 GPIO Example Program ............. 75 AIIS-5410P User Manual...
100 meters. AIIS-5410P offers rich I/O interfaces such as four PoE port channels, max, eight USB 3.0 ports, two serial ports on the front panel can be configured as RS-232, RS-422 or RS-485 via BIOS setting.
Two(2) SATA Revision 3.0 ports SATA Interface Legacy IED (Including IRQ)/Native AHCI appearance to OS Partial/Slumber power management modes with wake Capable of 6Gbit/s transfer rate PCH: Intel® QM170 Audio Link Intel® HD Graphics 530, support DirectX12 AIIS-5410P User Manual...
Page 16
Audio Codec: Realtek ALC892: Compliant with HD Audio specifications Audio Supports to 16/20/24-bit DAC and 16/20/24-bit ADC resolution Support: Line-out, Mic-in DAC supports 16/20/24-bit PCM format, multiple stereo recording Battery backup BR2032 3 V/190mAh AIIS-5410P User Manual...
2.2.1 Jumper description You may configure the AIIS-5410P to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
Clear CMOS 2.2.2.2 System AT/ATX mode function option AIIS-5410P support AT or ATX mode and Default is ATX module. if you want to change to AT mode that you can find AT/ATX mode jumper in motherboard. PSON1 System AT/ATX mode option...
PoE LED 4 x PoE ports 8 x USB3.0 ports Mic-In Remote Power LAN 1 & 2 Figure 2.1 AIIS-5410P Front View DIO port COM 1 & 2 CFast 32bit DIO module Figure 2.2 AIIS-5410P Rear View AIIS-5410P User Manual...
Page 23
Note! NC represents “No Connection”. 2.3.1.2 Digital I/O AIIS-5410P provides one DSUB-15 male connector which offers 4-ch digital input and 4-ch digital output and one pin support 5V power. Table 2.3: Digital I/O Connector Pin Assignments Signal Name Signal Name...
Page 24
2.3.1.3 Ethernet connector (LAN) AIIS-5410P is equipped with two Ethernet controllers that are fully compliant with IEEE 802.3u 10/100/1000 Mbps CSMA/CD standards. LAN1 is equipped with Intel ® i210IT and LAN2 is equipped with Intel i210IT. The Ethernet port provides a standard RJ45 jack connector with LED indicators on the front side to show its Active/Link sta- tus and Speed status.
Page 25
2.3.1.5 Audio Connector AIIS-5410P has two stereo audio ports with phone jack connectors, one Line_Out, one Mic_In. The audio chip is controlled by ACL892, and it’s compliant with AZALIA standard. Figure 2.5 Audio Connector Table 2.6: Audio Connector Pin Assignments...
Page 26
2.3.1.7 VGA Connector The AIIS-5410P provides a high resolution VGA interface with a 15-pin D-sub con- nector to support a VGA CRT monitor. It supports display resolution of up to 2048 x 1152 @ 60 Hz. Figure 2.7 VGA Connector Table 2.8: VGA Connector Pin Assignments...
Page 27
2.3.1.11 Power ON/OFF Button AIIS-5410P comes with a Power On/Off button with LED indicators on the front side to show its On status (Green LED) and Off/Suspend status (RED LED), that supports dual function of Soft Power-On/Off (instant off or delay 4 seconds), and suspend.
2.3.1.12 LED Indicators AIIS-5410P provides six LED. Two for HDD status and System abnormal status and four for PoE signal LED. Table 2.11: LED indicators for HDD status / System abnormal status LED Color Function System abnormal status LED* Amber...
Installation 2.4.1 HDD installation AIIS-5410P provide two 2.5” storage spaces. Undo 6 screws and remove the bottom cover. Undo 4 screws to remove HDD tray. AIIS-5410P User Manual...
Page 30
Secure the 4xHDD screws (P/N:1930002235) Assemble SATA cable/power cable and replace HDD tray to secure 4x screws. Replace bottom cover. AIIS-5410P User Manual...
2.4.2 Memory Installation AIIS-5410P system has 4GB memory on board; if you want to add more memory, please connect your distributor or sales representative to order compatible memory modules. Part numbers below: 4G SO-DDR4-2133 512X8 1.2V SAM P/N: AQD-SD4U4GN21-SG ...
Undo 2 screws to remove riser card bracket. Undo 4 screws to remove PCIe x8 riser card and replace with PCI riser card. Assemble riser card bracket and secure the screws and replace HDD bracket and bottom cover. AIIS-5410P User Manual...
2.4.6 AIIS-5410P MB IO connector Mimi-PCIe socket (Support m-SATA) ME setting Clear CMOS LPC Connector USB Connector (For 32bit DIO module) DDR4 socket ATX/AT module Jumper SATA Power Watch dog/OBS Extra 5V power Internal USB 2.0 80 Port LED AIIS-5410P User Manual...
With the AMI BIOS Setup program, you can modify BIOS settings and control the special features of your computer. The Setup program uses a number of menus for making changes and turning special features on or off. This chapter describes the basic navigation of the AIIS-5410P setup screens. AIIS-5410P User Manual...
System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS format. AIIS-5410P User Manual...
3.2.2 Advanced BIOS Features Setup Select the Advanced tab from the AIIS-5410P setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as ACPI Settings and hit <enter> to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>...
Page 39
3.2.2.1 Trusted Computing Security Device Support This item allows user to enable or disable “Security Device Support”. AIIS-5410P User Manual...
Page 40
ACPI Sleep State This item allows user to set ACPI mode S3 (Suspend to RAM) or to Disable “ACPI Sleep State”. PowerOn by Modem This item allows user to enable or disable “PowerOn by Modem”. AIIS-5410P User Manual...
Page 41
3.2.2.3 PCH-FW Configuration Firmware Update Configuration Me FW Image Re-Flash This item allows user to enable or disable "Me FW Image Re-Flash". AIIS-5410P User Manual...
Page 42
3.2.2.4 SMART Settings SMART Self Test This item allows user to enable or disable ”SMART Self Test". AIIS-5410P User Manual...
Page 43
3.2.2.5 NCT6106D Super IO Configuration AIIS-5410P supports 2 x RS-232/422/485 I/O port BIOS setup. AIIS-5410P User Manual...
Page 44
Change Settings This item allows user to change settings for the serial port. The default setting is "Auto". Device Mode This item allows user to set the mode for the serial port. The default setting is "RS-232". AIIS-5410P User Manual...
Page 45
This item allows user to enable or disable "Case Open Warning”. Note! AIIS-5410P system does not by default have a case open switch in the chassis. If your application needs a case open function, please contact your distributor or sales representative.
Page 46
3.2.2.7 S5 RTC Wake Settings Wake system from S5 This item allows user to enable system wake on alarm, or to set a fixed or dynamic wake time from S5 (soft power-off). AIIS-5410P User Manual...
Page 47
COM0 Console Redirection This item allows user to enable or disable "Console Redirection" the Serial Port for Out-of-Band Management/Windows Emergency Management Services (EMS) Console Redirection This item allows user to enable or disable "Console Redirection". AIIS-5410P User Manual...
Page 48
3.2.2.9 CPU Configuration AIIS-5410P User Manual...
Page 49
This item allows user to enable or disable "Intel(R) SpeedStep(tm)". Turbo Mode This item allows user to enable or disable "Turbo Mode". Intel TXT(LT) Support This item allows user to enable or disable "Intel TXT(LT) Support". AIIS-5410P User Manual...
Page 50
3.2.2.10 Intel TXT Information 3.2.2.11 SATA Controller AIIS-5410P User Manual...
Page 51
AIIS-5410P has two 2.5" storage bays, and supports one m-SATA and one CFast. SATA Controller(s) This item allows user to enable or disable "SATA Controller(s)". SATA Mode Selection This item allows user to set AHCI or RAID for "SATA Controller(s)".
Page 52
SATA Device Type This item allows user to set “SATA Device Type” to either Hard Disk Drive or Solid State Drive. Serial ATA Port 2 (AIIS-5410P CFast) Port 2 This item allows user to enable or disable "Port 2".
Page 53
3.2.2.12 PCI Devices Common Settings PCI Latency Timer This item allows user to set PCI Latency Timer to different modes. The default setting is "32 PCI Bus Clocks". AIIS-5410P User Manual...
Page 54
Video This item allows user to set Do not launch or UEFI or Legacy for "Video". Other PCI devices This item allows user to set Do not launch or UEFI or Legacy for "Other PCI devices". AIIS-5410P User Manual...
Page 55
This item allows user to set different time modes for "USB transfer Time-out". Device reset Time-out This item allows user to set different time modes for "Device reset Time-out". Device power-up delay This item allows user to set different time modes for "Device power-up delay". AIIS-5410P User Manual...
3.2.3 Chipset System Agent (SA) Configuration AIIS-5410P User Manual...
Page 57
This item allows user to set Auto or PEG11 or PEG 12 for "Primary PEG". Primary PCIE This item allows user to set PCIE channel, and default is "Auto". Internal Graphics This item allows user to set Auto, Disabled, or Enabled for "Internal Graphics". AIIS-5410P User Manual...
Page 58
Primary IGFX Boot Display This item allows user to set VBIOS Default or DVI1 or CRT for "Primary IGFX Boot Display". PEG Port Configuration This item allows user to set CPU PCI Expansion x16 GEN3. AIIS-5410P User Manual...
Page 59
This item allows user to set Auto, Gen1, or Gen2 or Gen3 for "Max Link Speed" at PCIe x16 or PCIe x8 socket. Detect Non-Compliance Device This item allows the system to detect non-compliant devices. Default is Dis- abled. AIIS-5410P User Manual...
Page 61
3.2.3.2 PCI Express Configuration AIIS-5410P User Manual...
Page 62
PCIe Speed This item allows user to set Gen1 or Gen2 or Gen3 for "PCIe Speed" and default is "Auto". Advanced Error Reporting This item allows user to set Disabled or Enabled for "Advanced Error Reporting" (AER). AIIS-5410P User Manual...
Page 63
3.2.3.3 USB Configuration USB Precondition This item allows user to disable or enable "USB Precondition". XHCI Disable Compliance Mode This item allows user to set FALSE or TRUE for "XHCI Disable Compliance Mode". AIIS-5410P User Manual...
Page 64
3.2.3.4 HD Audio Configuration HD Audio This item allows user to Disable, Enable, or set to Auto for "HD Audio". AIIS-5410P User Manual...
Page 65
This item allows user to set SO State, S5 State, or Last State for "State After G3". PCI Express Wake Disable This item allows user to disable or enable "PCI Express Wake Disable". High Precision Timer This item allows user to disable or enable "High Precision Timer". AIIS-5410P User Manual...
3.2.4 Security Administrator Password This item allows user to set an "Administrator Password" if desired. User Password This item allows user to set a "User Password" if desired. AIIS-5410P User Manual...
Quiet Boot This item allows user to disable or enable "Quiet Boot". Boot Option Priorities Note! These items will display based on how many devices are attached. – Boot Option #1 – Boot Option #2 AIIS-5410P User Manual...
This item allows user to Save as User Defaults. Restore User Defaults This item allows user to Restore User Defaults. Launch EFI Shell from file system device Attempts to Launch EFI Shell application (Shell.efi) from one of the available file system devices. AIIS-5410P User Manual...
4.1.1 Before you begin To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for the AIIS-5410P are located on the software installation CD. Note! The files on the software installation CD are compressed. Do not attempt to install the drivers by copying the files manually.
3D support deliv- ers an intensive and realistic visual experience. Caution! Intel® Graphic Device does not support Windows 10 (32bit) and Win- dows 8.1 (32.bit) AIIS-5410P User Manual...
"Intel ME" to install the driver. Note! ® ® If the Intel Management Engine (Intel ME) driver has not been suc- cessfully installed in Win7, please refer to the Win7 ME install process below. AIIS-5410P User Manual...
4.4.1 Introduction The AIIS-5410P has dual Gigabit Ethernet LANs via dedicated PCI Express x1 lanes (Intel® I219LM (LAN1) and I210IT (LAN2)) that offer bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet at 1000 Mbps.
In the following sections, refer to the one that provides the driver setup procedure for the operating system you are using. 4.4.4 Windows 10 /Windows 8.1 /Windows 7 Insert the driver CD into your system's CD-ROM drive. Select folder "04_LAN" then click the "Rel_20.3_PV_OEMGen_380842" AIIS-5410P User Manual...
Install USB3.0 4.6.1 Introduction AIIS-5410P provides 8x USB 3.0 and the data transfer rate of USB3.0 (5Gb/s) is 10 times that of USB2.0 (480 Mbps). Insert the driver CD into your system’s CD-ROM drive. Navigate to the "07 USB3.0" to install the drier.
Programming the Watchdog Timer The AIIS-5410P's watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to pro- gram it.
Page 79
Unlock NCT6106D Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog timer Lock NCT6106D AIIS-5410P User Manual...
Page 80
Bit 5: Write 1 to generate a timeout signal immedi- ately and automatically return to 0. [default=0] Bit 4: Read status of watchdog timer, 1 means timer is “timeout”. AA (hex) ----- Write this address to I/O port 2E (hex) to lock the watchdog timer 2. AIIS-5410P User Manual...
Inc dx Mov al,10 Out dx,al ;----------------------------------------------------------- Dec dx ; Lock NCT6106D Mov al,0aah Out dx,al Enable watchdog timer and set 5 minutes as timeout interval ;----------------------------------------------------------- Mov dx,2eh ; Unlock NCT6106D Mov al,87h Out dx,al Out dx,al AIIS-5410P User Manual...
Page 82
Enable watchdog timer to be reset by mouse ;----------------------------------------------------------- Mov dx,2eh ; Unlock NCT6106D Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- AIIS-5410P User Manual...
Page 83
Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f2h Out dx,al Inc dx In al,dx Or al,40h Out dx,al AIIS-5410P User Manual...
Page 84
Dec dx ; Generate a time-out signal Mov al,0f2h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------- Dec dx ; Lock NCT6106D Mov al,0aah Out dx,al AIIS-5410P User Manual...
Extended Function Index Registers (EFIRs) The EFIRs are write-only registers with port address 2Eh or 4Eh on PC/AT systems. Extended Function Data Registers (EFDRs) The EFDRs are read/write registers with port address 2Fh or 4Fh on PC/AT systems AIIS-5410P User Manual...
MOV AL, E5H OUT DX, AL MOV DX, 2FH MOV AL, ??H ; Put the output value into AL OUT DX, AL ------------------------------------------------------------ Exit extended function mode | ------------------------------------------------------------ MOV DX, 2EH MOV AL, AAH OUT DX, AL AIIS-5410P User Manual...