Subscribe to Our Youtube Channel
Related Manuals for BCM EBC-3615
Summary of Contents for BCM EBC-3615
- Page 1 Quick Installation Guide EBC-3615/3615L All-in-One Transmeta TM5400 Single Board with Dual LCD, AC97 Audio, & Dual 10/100Base-Tx Ethernet Ed. – 8 April 2002...
- Page 2 ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE. EBC-3615/3615L Quick Installation Guide...
-
Page 3: Copyright Notice
Brand and product names are trademarks or registered trademarks of their respective owners. Disclaimer BCM Advanced Research. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. BCM Advanced Research assumes no responsibility... -
Page 4: Life Support Policy
Whether your new BCM device is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name BCM has come to be known. - Page 5 Our dealers are well trained and ready to give you the support you need to get the most from your BCM’s products. In fact, most problems reported are minor and are able to be easily solved over the phone.
- Page 6 If any of BCM’s products is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time, and freight.
-
Page 7: Packing List
Packing List Before you begin installing your single board, please make sure that the following materials have been shipped: 1 EBC-3615/3615L All-in-One Transmeta TM5400 Computing Module 1 Quick Installation Guide 1 Audio jacks and USB connector daughter board 1 CD-ROM contains the followings: —... -
Page 8: Safety Precautions
CPU card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static-shielded bag when they are not in the chassis. EBC-3615/3615L Quick Installation Guide... - Page 9 Quick Installation Guide 2. Jumper & Connector Jumper & Connector Layout EBC-3615/3615L Quick Installation Guide 9...
- Page 10 Clear CMOS & PC/104+ voltage select 3 x 2 header, pitch 2.0mm J5, J6 COM2 RS-232/422/485 select 3 x 2 header, pitch 2.0mm 6 x 2 header, pitch 2.0mm (J5) ATATX1 AT / ATX power select 3 x 1 header, pitch 2.0mm EBC-3615/3615L Quick Installation Guide...
- Page 11 5 x 2 header, pitch 2.0mm USB1 VGA1 CRT connector DB-15 female connector LCD backlight brightness adjustment 3 x 1 header, pitch 2.54mm connector STN LCD contrast adjustment connector 3 x 1 header, pitch 2.54mm EBC-3615/3615L Quick Installation Guide 11...
-
Page 12: Hardware Configuration
PC/104+ Voltage Select (J1 / Pin 2, 4, 6) You can select the PC/104+ signal voltage by setting Pin 2-4-6 of J1. The following charts show the available option. PC/104+ Signal Voltage Select (J1 / Pin 2, 4, 6) 3.3V * default EBC-3615/3615L Quick Installation Guide... - Page 13 Quick Installation Guide 3.1.3 COM2 RS-232/422/485 Select (J5, J6) The EBC-3615 COM2 serial port can be selected as RS-232, RS-422, or RS-485 by setting J5 & J6. COM2 RS-232/422/485 Select (J5, J6) RS-232* RS-422 RS-485 * default EBC-3615/3615L Quick Installation Guide 13...
- Page 14 (and J2 to 2-3 closed), if ATX power supply is to be used. AT/ATX Power Select (ATATX1) AT P/S ATX P/S* ATATX1 * default Note: Set J2 to 2-3 closed, if AT power supply is to be used. EBC-3615/3615L Quick Installation Guide...
- Page 15 Quick Installation Guide Connector Definitions 3.2.1 IrDA Connector (CN2) Signal IRRX IRTX 3.2.2 Secondary LCD Panel Connector (CN3) Signal Signal 3.3V 3.3V Vcon LVDSCLK ENVEE ENBKL EBC-3615/3615L Quick Installation Guide 15...
- Page 16 EBC-3615/3615L 3.2.3 Primary LCD Panel Connector (CN4) Signal Signal 3.3V 3.3V Vcon SHFCLK ENVEE ENBKL EBC-3615/3615L Quick Installation Guide...
- Page 17 Enable backlight signal. This signal is controlled as a part of the panel power sequencing ENVEE Enable VEE. Signal to control the panel power-on/off sequencing. A high level may turn on the VEE (LCD bias voltage) supply to the panel EBC-3615/3615L Quick Installation Guide 17...
- Page 18 EBC-3615/3615L 3.2.5 Signal Configuration – DSTN & TFT Panel Displays (CN4, CN3) DSTN Pin name 16-bit 24-bit 9-bit 12-bit 18-bit 24-bit 12-bit x 2 UD11 UD10 LD11 LD10 EBC-3615/3615L Quick Installation Guide...
- Page 19 FP2_R5 FP2_R4 FP2_R3 FP2_R2 FP2_R1 FP2_R0 FP2_G7 FP2_G6 FP2_G5 FP2_G4 FP2_G3 FP2_G2 FP2_G1 FP2_G0 FP2_B7 FP2_B6 FP2_B5 FP2_B4 FP2_B3 FP2_B2 FP2_B1 FP2_B0 FP2_VSYNC FP2_HSYNC FP1_R5 FP1_R4 FP1_R3 FP1_R2 FP1_R1 FP1_R0 FP2_DE FP1_G5 FP1_G4 FP1_G3 FP1_G2 EBC-3615/3615L Quick Installation Guide 19...
- Page 20 TFT panel is insufficient. 3.2.6 CD-ROM Audio Input Connector (CN5) Signal CD_R CD_GND CD_L CD_GND 3.2.7 Audio Connector (CN6) Signal Signal Mic Bias Mic-In Line-In L Line-In R Line-Out L Line-Out R EBC-3615/3615L Quick Installation Guide...
- Page 21 Quick Installation Guide 3.2.8 Serial Port 2 with External DB9 Connector (CM1) Signal Signal 3.2.9 Pin Header Serial Port 2 Connector in RS-232 Mode (CM2) Signal Signal EBC-3615/3615L Quick Installation Guide 21...
- Page 22 Pin Header Serial Port 2 Connector in RS-422 Mode (CM2) Signal Signal 3.2.11 Pin Header Serial Port 2 Connector in RS-485 Mode (CM2) Signal Signal DATA- DATA+ 3.2.12 ATX Power Connector (J2) Signal PS_ON VCC_SB 3.2.13 USB Connector (USB1) Signal Signal VCC2 VCC1 EBC-3615/3615L Quick Installation Guide...
- Page 23 Quick Installation Guide 3.2.14 Power Connector (PWR1) Signal 3.2.15 Auxiliary Power Connector (PWR2) Signal -12V 3.2.16 TV Out Connector (TV1) Signal CVBS EBC-3615/3615L Quick Installation Guide 23...
- Page 24 EBC-3615/3615L 3.2.17 LCD Backlight Brightness Adjustment Connector (VR1) Signal CN5 pin 4 Variation Resistor (Recommended: 4.7KΩ, >1/16W) 3.2.18 STN LCD Contrast Adjustment Connector (VR2) Signal VCON EBC-3615/3615L Quick Installation Guide...
Need help?
Do you have a question about the EBC-3615 and is the answer not in the manual?
Questions and answers