GE Profile JD968KFCC Specifications

JD968BF/KF/SF/TF – GE Profile
Dimensions (in inches)
30" Min.
6" Min.
from walls
30" Min.
23-3/16
If necessary,
build upsides
to 1-1/4" thick 27-1/2
to provide
countertop
36
support
30
24
2-7/8"
To Front Surface
of Countertop
20-5/8" Door
Clearance
From Front
Surface of
Countertop
Specification Revised 1/08
220822
30" Drop-In Electric Range
™
Shave Raised Edge To Clear
31-1/8" Wide Control Panel
Excluding Models JDS28 and JDP39
9/16
6" Min.
from walls
Acceptable Electrical Outlet
Area Also In Adjacent
18" Min.
Cabinet Or Under Floor
Conduit is 40" long
25
If necessary,
build upsides
to 1-1/4" thick
to provide
7-1/2
countertop
36
support
Accessory
Backguard
A/B*
31-1/4
2-7/8"
To Front Surface
of Countertop
27
*JXS37 is 5-1/4" and JXS32 is 4"
26-1/2**
**Total depth from wall to
(excluding handle)
front of closed oven door
including handle is 29-1/2.
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
Shave Raised Edge To Clear
31-1/8" Wide Control Panel
30" Min.
Excluding Models JDS28 and JDP39
9/16
30" Min.
Acceptable Electrical Outlet
23-3/16
Area Also In Adjacent
18" Min.
Cabinet Or Under Floor
Conduit is 40" long
25
27-1/2
7-1/2
30
Accessory
Backguard
24
31-1/4
KW Rating
240V 12.1
208V 9.1
27
Breaker Size
20-5/8" Door
240V 40 Amps
Clearance
From Front
Surface of
208V 40 Amps
Countertop
*JXS37 is 5-1/4" and JXS32 is 4"
26-1/2**
**Total depth from wall to
(excluding handle)
front of closed oven door
including handle is 29-1/2.
Listed by
Underwriters
Laboratories
Optional Kits For Drop-In Electric Ranges
(Available At Additional Cost)
Maintop Filler
(Fills gap between cooktop and wall
when unit is installed in 30"
free-standing cutout)
JXS66WW—White
JXS66CC—Bisque
JXS66BB—Black
Accessory Backguards
(Attaches to the back of range as a
backguard when unit is installed in
30" free-standing cutout)
JXS37WW—White
JXS37CC—Bisque
JXS37BB—Black/Stainless
Note: Cabinets installed adjacent to drop-in electric ranges must have an
adhesion spec of at least a 194°F temperature rating.
Note: All 30" Drop-In Radiant Ranges conform to U.L. requirements for 0"
A/B*
spacing from range to adjacent walls below countertop. To reduce possibility
of scorching the side walls above the countertop when no load is present on
burners, it is recommended that a minimum 6" spacing from adjacent side
wall be allowed for possible extended high-heat element operation.
Installation Information: Before installing, consult installation instructions
packed with product for current dimensional data.
IMPORTANT: 30" DROP-IN RANGES ARE DESIGNED TO HANG
FROM THE COUNTERTOP. IT DOES NOT REST ON THE FLOOR.
FOR INSTALLATION ALTERNATIVES, REFER TO INSTALLATION
INSTRUCTIONS PACKED WITH PRODUCT.
For answers to your Monogram, GE Profile
®
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center service, 800.626.2000.
®
Lower Trim Kits
(When a drop-in is installed in an
existing cutout greater than 27-1/4"
from the counter to the cabinet
cross-rail, a lower trim kit should be
used to fill the gap at the bottom of
the range)
JXS96WW—White
JXS96CC—Bisque
or
™