Page 2
Precautions Precautions With Small Children Beginning a Run • For children under the age of 13, parential guidance 1. Place the R/C car so that the wheels are off the ground. is recommended when running. 2. Confirm that the speed controller switch is OFF, and connect the motor and battery.
Shock Assembly Bag A 555-44816 Shock Piston 555-44670 E-Clip 555-44702 Shock Shaft 555-44816 Shock Shaft Guide 555-44806 555-44858 3x6x0.5mm Washer O-Ring 555-44816 Shock Body Insert shaft guide and oil ring into shock shaft as shown in diagram. Make sure the shaft 555-44859 guide is fully seated in the O-Ring (Black)
Page 5
Shock Assembly Continued Bag A 555-44706 5.8mm Flanged Pivot Ball 555-44814 Shock Cap (Black) 555-44816 555-44706 Upper Ball End 5.8mm Flanged 555-44813 Pivot Ball Shock 555-44670 Diaphram E-Clip 555-44816 555-44702 Shock Piston Shock Shaft 555-44816 Shaft Guide 555-44858 555-44806 O-Ring 3x6x0.5mm Washer 555-44816...
Page 6
Front & Rear End Assemblies Bag B 555-44726 Differential Case 555-44732 10x15x4mm Bearing 555-44738 555-44857 Planetary Gear 10x12.5x0.1mm Shims 555-44738 Sun Gear 555-44817 555-44758 555-4473210x15x- Ring Gear M1x30T M2x8mm FH 4mm Bearing Use Grease 555-44879 O-Ring (Black) Assembly x2 555-44819 Drive Cup 555-44856 5x7x0.2mm Shims...
Page 7
Front End Assembly Bag B 555-44704 4-Link Bracket 555-44694 Differential Cover 555-44694 Solid Axle 555-44776 M3x18mm BH 555-44746 M2.5x18mm BH 555-44724 555-44724 About 3-3.5 mm C Hub _ B C Hub _ A 555-44678 King Pin Front Front Castor Angle Adjustment: Recommended at the highest point, refer to the diagram.
Page 8
Front End Assemblies Continued Bag B 555-44698 Lower Link (275WB) 555-44707 5.8mm Pivot Ball 555-44698 Upper Link (275WB) 555-44766 M3x14mm BH 555-44800 About 10.3 mm 555-44766 M3x25mm Turnbuckle M3x14mm BH 555-44708 555-44778 5.8mm Rod End M3x30mm BH 555-44708 555-44706 5.8mm Rod End 5.8mm Flanged Pivot Ball 555-44776 555-44808...
Page 9
Front End Assemblies Continued Bag B 555-44706 5.8mm Flanged Pivot Ball 555-44766 555-44708 M3x14mm BH 5.8mm Rod End 555-44804 About 71.1mm M3x90mm Turnbuckle 555-44708 5.8mm Rod End 555-44706 5.8mm Flanged Pivot Ball...
Page 11
Front & Rear End Assemblies Bag B 555-44698 Lower Link (275WB) 555-44707 5.8mm Pivot Ball 555-44698 Upper Link (275WB) 555-44766 M3x14mm BH Rear End Assembly...
Page 12
Center Differential Assembly Bag C 555-44736 5x8x2.5mm Bearing Use Threadlocker Use Grease 555-44722 555-44825 Transmission Gear Box A Gear (Metal) 555-44722 Transmission Gear Box 555-44734 Adjuster Cap 5x10x4mm Bearing 555-44734 5x10x4mm Bearing 555-44794 M3x8mm Cap 555-44855 2.8mm Pin 555-44825 Idle Gear (Metal) 555-44700 Gear Shaft...
Page 13
Center Differential Assembly Continued Bag C 555-44760 555-44854 M3x8mm Cap 2x10mm Pin 555-44830 Use Threadlocker Slipper Hub Set Use Grease 555-44824 48P 85T Spur Gear 555-44831 555-44794 Slipper Spring M3x8mm Cap 555-44740 M4 Nylon 555-44826 Locknut Slipper Pad 555-44852 M3x6mm Cap 555-44710 5x10mm Thrust Bearing...
Page 14
Center Differential Assembly Continued Bag C 555-44840 555-44840 ST Wiper C ST Wiper A 555-44840 ST Wiper B 555-44678 King Pin 555-44680 Use Threadlocker Use Threadlocker RS 550 Motor 555-44827 48P 16T Motor Pinion Gear 555-44843 Motor Heat Sink Plate Set the gear mesh about 0.1mm gap 555-44784...
Page 15
Center Differential Assembly Continued Bag C 555-44722 Transmission Gear Box Cover 555-44829 O-Ring (Black) 555-44720 Drive Cup (4.5mm) 555-44838 Skid Plate 555-44792 M3x8mm BH 555-44829 O-Ring (Black) 555-44720 Drive Cup (4.5mm) 555-44790 M3x6mm FH...
Wheels & Tires Bag H 555-44728 Monster Truck Tires Right Left Assembly 555-44658 2.2” Monster Truck Wheels 2 Left & 2 Right 555-44730 (Orange) 555-44731 (Red) Bead Lock Ring We recommend using CA Glue to ensure a secure attachment. 555-44796 M4 Serrated Flange Lock Nuts...
Page 25
Sway Bar Assembly 555-44860 555-44860 555-44860 555-44860 Sway Bar Link Sway Bar Arm A Sway Bar Arm B Sway Bar Link 555-44764 555-44764 M3x12mm BH M3x12mm BH 555-44774 M3x17mm FH 555-44860 555-44860 Pivot Block A Pivot Block B 555-44707 555-44707 5.8mm Ball 5.8mm Ball 555-44662...
Page 26
Sway Bar Assembly Continued 555-44863 6x8x0.2mm Washer (Shims may vary.) 555-44776 M3x18mm BH 555-44776 M3x18mm BH 555-44776 555-44863 M3x18mm BH 6x8x0.2mm Washer (Shims may vary.) 555-44776 M3x18mm BH When installing the Tension Bar, make sure Use Threadlocker to push it all the way in and tighten it with an M3x5mm screw.
555-44746 115. 555-44849 Hooligan Roll Cage and Light Housing M2.5 x 6 mm Button Head Socket Screw (10 pcs.) 116. 555-44850 Torch Painted Body with Decal 555-44748 M2.5 x 8 mm Hex Head Socket Screw (10 pcs.) 555-44750 117. 555-44851 Torch Clear Body with Decal M2 x 5 mm Cap Screw (10 pcs.)