GE Profile Advantium PSB1000N Installation Instructions Manual
GE Profile Advantium PSB1000N Installation Instructions Manual

GE Profile Advantium PSB1000N Installation Instructions Manual

120 built-in speedcook ovens
Hide thumbs Also See for Profile Advantium PSB1000N:
Table of Contents

Advertisement

Available languages

Available languages

Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
for local inspector's use.
IMPORTANT
codes and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions for
future reference.
• Skill level - Installation of this appliance requires
basic mechanical and electrical skills.
• Completion time - 1 hour
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty. See Owner's
Manual for warranty information
IMPORTANT:
• Use this oven only for its intended purpose.
• Never use the oven for warming or heating a
room. Prolonged use of the oven without proper
ventilation can be hazardous.
CONTENTS
Design Information
Models Available .................................................................... 2
Product Dimensions and Clearances .......................... 2
Tools Required ........................................................................ 2
Parts Supplied ........................................................................ 2
Advance Planning ................................................................ 3
Electrical Requirements .................................................... 4
Prepare the Opening ...................................................... 5, 6
Remove the Packaging ...................................................... 6
- Save these instructions
- Observe all governing
.
Profile Advantium
SpeedCook Ovens
CAUTION:
For personal safety, remove house fuse or oven
circuit breaker before beginning installation to avoid
severe or fatal shock injury.
CAUTION:
For personal safety, the mounting surface must be
capable of supporting the cabinet load, in addition
to the added weight of the 75-pound product, plus
additional oven loads of up to 50 pounds or a total
weight of 125 pounds.
CAUTION:
For personal safety this product cannot be
installed in cabinet arrangements such as an island,
a peninsula or below a countertop.
For a Spanish version of this manual,
visit our Website at GEAppliances.com.
Para consultar una version en español
de este manual de instrucciones, visite
nuestro sitio de internet GEAppliances.com.
Installation Instructions
Step 1, Slide the Oven into the Cutout ........................ 7
Step 2, Install Bottom Trim ................................................ 7
Step 3, Install Mounting Screws ...................................... 8
Step 4, Finalize Installation................................................ 8
MFL59060902
120 Built-In
PSB1000 PSB1001
49-40607 02-09 JR

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Profile Advantium PSB1000N and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GE Profile Advantium PSB1000N

  • Page 1: Table Of Contents

    Installation Instructions Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT • — Save these instructions for local inspector’s use. IMPORTANT • — Observe all governing codes and ordinances.
  • Page 2: Models Available

    MODELS AVAILABLE Profile Models: PSB1000WW – White PSB1000BB – Black PSB1001SS – Stainless Steel PRODUCT DIMENSIONS AND CLEARANCES 22-9/16" 1-1/8" 21-1/2" 13/16" TOOLS REQUIRED • #2, Phillips screwdriver • Handheld drill • High-speed drill bit, 1/8" diameter • 3/8", slot-head screwdriver Design Information 13"...
  • Page 3: Advance Planning

    • The front surface of the oven will be nearly flush with surrounding cabinetry doors. • This oven can be installed over any GE single electric built-in oven or a warming drawer or both. IMPORTANT: This oven is not approved for use above another built-in SpeedCook oven, a side-by-side installation or below a countertop.
  • Page 4: Installation Preparation

    ELECTRICAL REQUIREMENTS Single Advantium 120 Installation: This product requires a 120-volt, 60 Hz, 15-amp circuit and draws 1.8 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. • Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating.
  • Page 5 PREPARE THE OPENING The Advantium 120 can be installed in combination with other GE appliances. Always follow each product’s Installation Instructions to complete the installation. Single Advantium 120 Installation: Order a 27"-wide single oven cabinet or cut the opening in a wall to the dimensions shown.
  • Page 6: Prepare The Opening

    25-1/8" 17-1/2" 45-1/4" Min. *If you are replacing a GE electric double oven with the combined installation of an Advantium 120 and a single oven, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 2" minimum shown.
  • Page 7: Step 1, Slide The Oven Into The Cutout

    DO NOT USE THE HANDLE TO LIFT THE OVEN. DAMAGE WILL OCCUR! • Lift and hold the oven at the front of the opening. Hold the oven at a 45º angle and plug in the power cord.
  • Page 8: Step 3, Install Mounting Screws

    INSTALL MOUNTING SCREWS • Drill pilot holes through the side flanges, 2 on each side. • Drive the color-matched screws into the side flange. FINALIZE INSTALLATION • Turn the power on at the source. The interior light should come on when the door is opened. •...
  • Page 9 Instrucciones de instalación ¿Preguntas? Llame al 800.GE.CARES (800.432.2737) o bien visite nuestra página Web: GEAppliances.com ANTES DE INICIAR Lea estas instrucciones completa y cuidadosamente. IMPORTANTE • — Guarde estas instrucciones para uso del inspector local. IMPORTANTE • — Observe todos los códigos y órdenes de ley.
  • Page 10: Información Sobre El Diseño

    Información sobre el diseño MODELOS DISPONIBLES Modelos Profile: PSB1000WW – Blanco PSB1000BB – Negro PSB1001SS – Acero inoxidable DIMENSIONES DEL PRODUCTO Y ESPACIO LIBRE 22-9/16" 1-1/8" 21-1/2" 13/16" HERRAMIENTAS NECESARIAS • Destornillador Phillips N.°2 • Taladro manual • Broca para taladro de alta velocidad de 1/8" de diámetro •...
  • Page 11: Planificación Anticipada

    • Este horno puede instalarse sobre cualquier horno empotrado individual GE o sobre un cajón calentador, o ambos. IMPORTANTE: Este horno no está aprobado para usarlo sobre otro horno SpeedCook empotrado, una instalación pegada a otra o debajo de una...
  • Page 12: Preparación Para La Instalación

    Preparación para la instalación REQUISITOS ELÉCTRICOS Instalación única del Advantium 120: Este producto requiere un circuito de 120 voltios, 60 Hz, 15 amp y toma 1.8 kilovatios. Este producto debe conectarse a un circuito de alimentación del voltaje y la frecuencia adecuados. •...
  • Page 13 Preparación para la instalación PREPARE LA ABERTURA El Advantium 120 puede instalarse en combinación con otros aparatos GE. Siempre siga las indicaciones de instalación de cada producto para realizar la instalación. Instalación única del Advantium 120: Pida una alacena para horno único de 27"...
  • Page 14: Prepare La Abertura

    17-1/2" Min. 45-1/4" *Si está reemplazando un horno eléctrico doble GE por la instalación combinada de un Advantium 120 y un horno único, use las dimensiones indicadas. Es posible que el riel del medio que separa las dos aberturas deba ser mayor que el mínimo de 2"...
  • Page 15: Instalación

    DESLICE EL HORNO DENTRO DEL CORTE PRECAUCIÓN: Se requieren dos personas para levantar el horno e introducirlo en la abertura. Agarre la parte inferior por delante y por detrás. NO USE LA MANIJA PARA LEVANTAR EL HORNO. ¡PUEDE DAÑARSE! • Levante y sostenga el horno delante de la abertura.
  • Page 16: Paso 3, Instale Los Tornillos De Montaje

    INSTALE LOS TORNILLOS DE MONTAJE • Realice orificios piloto con el taladro en los salientes laterales, 2 de cada lado. • Coloque los tornillos de color combinado en el saliente lateral. FINALICE LA INSTALACIÓN • Conecte la energía en la fuente. La luz interior se encenderá...

Table of Contents