Page 1
O P E R A T O R ' S M A N U A L LIQUID SPRAYER LS2006 LS2006 5CS2006OM (rev 00 07/2020)
Page 2
TO THE OWNER: Read this manual before operating your Frontier equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all the adjustment and operating procedures before attempting to operate.
TABLE OF CONTENTS INTRODUCTION SAFETY Safety and Instructional Labels ASSEMBLY INSTALLATION OPERATION SERVICE TROUBLESHOOTING SPECIFICATIONS Tractor Ballasting Parts Diagrams Bolt Torque Chart This Operator's Manual should be regarded as part of the machine. Suppliers of both new and second-hand machines must make sure that the manual is provided with the machine.
Frontier dealer to inform them of this unit's possible in-line production changes, your serial number. This will help Frontier notify you machine may vary slightly in detail.
Page 5
Riders road. Contact your Frontier dealer to obtain may also obstruct the operator’s view, the recommended light kit. resulting in the machine being operated in an unsafe manner.
Page 6
Direct exposure to hazardous chemicals repairs. can cause serious injury. Potentially • Before servicing machine or attachment, hazardous chemicals used with Frontier carefully release pressure from any equipment include pesticides, herbicides components with stored energy, such as and fungicides. hydraulic components and springs.
Page 7
• Never dump solution into a drain or near a road. Contact your Frontier dealer to obtain lake or stream. the recommended light kit. •...
ST50927 3 - 5CS50929 4 - Serial Number Tag LS2006 60 GALLON LIQUID SPRAYER Mfg Date: MM/DD/YYYY Serial Number *XXXXXXXXXXXXXXXXX* Mass (Empty): 109 - 230 Lbs (49 - 104 Kg) Mass (Laden): 651 - 793 Lbs (295 - 360 Kg)
Page 9
SAFETY AND INSTRUCTIONAL LABELS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Damaged or Missing Labels Immediately! (Safety Decals continued from previous page) Safety 5CS2006OM (rev 00 07/2020)
ASSEMBLY Dealer Set-Up Instructions Assembly of this equipment is the responsibility of the Frontier dealer. It should be delivered to the owner completely assembled and adjusted for normal operating conditions. In most cases the sprayer will be shipped completely assembled except for the boom and optional 100 ft hose reel kit.
Page 11
3. Connect hoses: • For 12 ft Boom and Boomless: 4. For the two outside booms, use wire ties (I) • Connect and tighten the wingnut on the to secure hoses to the back of the booms hose (D) from the valve to the threaded about 1 foot away from the hinge on either fitting (E) in the center of the boom.
Page 12
6. Attach free end of 1/2" hose from Hose Reel to Tee Fitting (L) and secure with 1/2" screw type hose clamp (M). 3. Loosely Install Crossmember (E) using four 5/16" x 3/4" Carriage Bolts (F) and four 5/16" Flange Nuts (G) as shown. 4.
INSTALLATION Sprayer Installation Attaching Sprayer to Tractor 1. Park machine safely. (See Park Machine Safely in Safety section.) Installing Ballast 2. Lower tractor's 3-pt hitch to lowest position. 3. Mount sprayer on 3-point hitch. CAUTION: Avoid Injury! Machine can become unstable when operating with Attaching the Sprayer to Tractor with attachment.
Page 14
Removing and Storing Sprayer 1. Open drain valve and drain excess fluid into chemical disposal container. (See Dispose of Waste Properly in Safety section.) Removing Sprayer from Tractor 2. Rinse tank, pump, spray wand and all hoses thoroughly with fresh clean water. CAUTION: Avoid Injury! When the 3.
OPERATION Sprayer Setup 1. The preferred method of cleaning is to dilute remaining material with water and apply it to the area previously treated. Filling Sprayer Tank • If excess material remains, open drain valve and empty remaining material into CAUTION: Chemicals can be an appropriate container for reuse or for dangerous.
Page 16
1. Measure a 200 or 300 foot distance on a W = Nozzle spacing in inches field or surface similar to where sprayer will GPM Per Nozzle = GPA x MPH x W / 5940 be used. GPM Per Nozzle = GAL/1000 sq ft x MPH x W 2.
Page 17
Silver Series pump with Teflon rollers. rate that was used to determine tractor speed. Frontier part number 5CS43649. 1. Loosen lock ring (A) and adjust knob (B) to • Do not run pump dry! Do not pump faster or desired pressure.
Page 18
for leaks. Boomless Spray Width 4. Prepare to spray by turning section control • 2.5 ft - Both left and right sections OFF. valves to OFF. • 12 ft - Either left or right section OFF. 5. Start tractor and engage PTO. For adequate •...
Page 19
Spraying with the Spray Nozzle CAUTION: Avoid Injury! DO NOT use spray gun while tractor is in motion. 1. Turn all Section Control Valves to OFF. 2. Squeeze the handle (A) to spray. 3. Adjust mist to stream using lever (B). 4.
SERVICE Servicing Sprayer CAUTION: Avoid injury! Do not use standard antifreeze. Standard antifreeze can be harmful to humans, Servicing Sprayer Safely animals, crops and the environment. CAUTION: Chemicals can be 1. Empty and rinse tank. dangerous. Avoid injury to operator 2.
Page 21
Frontier Quality Continues with Quality NOTE: Due to normal wear, Teejet® recom- Service mends replacing sprayer nozzles after every Frontier provides a process to handle your spraying season. Nozzle replacement will questions or problems, should they arise, to ensure accurate spraying performance.
TROUBLESHOOTING Troubleshooting Sprayer Using the Troubleshooting Chart If you are experiencing a problem that is not listed in this chart, see your authorized dealer for service. When you have checked all the possible causes listed and you are still experiencing the problem, see your authorized dealer.
SPECIFICATIONS Boom Option 12.5 ft 18 ft Boomless Capacity Sprayer Tank 60 gal (227 L) Working Width 12.5 ft (3.8 m) 18 ft (5.5 m) 24 ft (7.3 m) Transport Width 52 in (132 cm) 77 in (196 cm) 35 in (89 cm) Dimension Transport Length 43 in (109 cm)
Operator’s Manual. 3. Stay away from chemicals, spray, and drift. 3. Stay away from chemicals, spray, and drift. LS2006 4. Before servicing or filling sprayer, lower all equipment to the 4. Before servicing or filling sprayer, lower all equipment to the ground, set the park brake, stop the engine, and remove the key.
Page 26
OM and Safety Decal Kit - 5CS0031 Spanish and Warning Label 5CS43994 Replacement Decal Kit - English Includes Qty. 3 Frontier Decal, 5CS43995 Replacement Decal Kit - French Qty. 2 Model Decal, Caution 5CS43996 Replacement Decal Kit - Spanish Label and...
Page 27
Plumbing PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS43648 60 Gallon Tank 5CS43175 Tank Lid 6” 5CS43981 Garden Hose Shut-off Valve 5CS43626 Tank Fitting 3/4” 5CS43633 Elbow 3/4” MP - 3/4” barb 5CS43660 45° Street Fitting 3/4” 5CS43661 Jet Agitator 5CS43739 Anti Vortex Plate 5CS43627...
Page 28
Plumbing PART ITEM NO. DESCRIPTION QTY. Note NUMBER QTY 4 for 18ft Boom, 5CS43630 3/4” Pipe Nipple Qty 2 for 12.5 ft Boom & 24ft Boomless 5CS43629 Single Union Ball Valve 5CS43631 Filter 5CS43632 Fitting 3/4” MP - 1” Hose QTY 3 for 18ft Boom, 5CS43634 Control Valve...
Page 30
Hoses PART ITEM NO. DESCRIPTION QTY. Note NUMBER For 30 ft Hand Sprayer - CTL 360”, MF 5CS43418 1/2” Hose For 100 ft Hose Reel - CTL 1200” MF 5CS43418 Hose Clamp Screw Type 3/8” - 5CS43652 Not Illustrated 1/2” 5CS43653 Hose Clamp Screw Type 3/4”...
Page 31
Frame Parts Diagrams 5CS2006OM (rev 00 07/2020)
Page 32
Frame PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS61500 3 Point A Frame 5CS43603 Channel Left 5CS43602 Channel Right 5CS43605 Front Brace 5CS43618 Support 03H1495 3/8” x 1-1/2” Carriage Bolt 03H1500 3/8” x 1” Carriage Bolt E55662 3/8" Flange Nut 5CS43883 Rear Crossmember 03H1540...
Page 33
30 ft Hand Sprayer PART ITEM NO. DESCRIPTION QTY. Note NUMBER A22698 5/16” Flange Nut N10217 1/4” Flange Nut 5CS62008 1/4” Bent Pin 5CS62006 Hose Hanger T58694 5/16” x 5/8” Flange Bolt 5CS43663 Hose Holder 1/2” 5CS43435 Sprayer Handgun CTL 360", MF 1/2"...
Page 34
6 Roller PTO Pump PART ITEM NO. DESCRIPTION QTY. Note NUMBER N167649 5/16” x 1/2” Flange Bolt A22698 5/16” Flange Nut 03H1540 5/16” x 3/4” Carriage Bolt 5CS43638 Elbow 3/4” MP - 1” barb 5CS43639 PTO Quick Connect Adapter 34 Parts Diagrams 5CS2006OM (rev 00 07/2020)
Page 35
6 Roller PTO Pump PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS50268 Chain 2/0 - 1.5 ft 5CS43650 Chain Latch 5CS43622 Pump Mount Angle 5CS43637 Pump Cast 6 Roller 5CS43649 Pump Silver Series 6 Roller 5CS43633 Elbow 3/4” MP - 3/4” barb Parts Diagrams 5CS2006OM (rev 00 07/2020)
Page 36
12.5' Folding Boom PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS60085 Side Boom Tube 37” 5CS60083 Center Boom Tube 48” 5CS43849 Boom Hinge Bracket 5CS43389 Boom Hinge Backing Plate 5CS43402 5/16” x 3” Clevin Pin 5CS43401 Plastic End Cap 1” 5CS43624 Small Bowtie Clip 5CS43598...
Page 37
12.5' Folding Boom PART ITEM NO. DESCRIPTION QTY. Note NUMBER N10217 1/4” Flange Nut 03H1810 1/4” x 1-1/2” Carriage Bolt FH325451 1/4” x 3” Carriage Bolt 5CS43597 Tee 1/2” Barb - 1/2” NPT F 5CS43658 Nozzle Body Single Hose 1/2” 5CS43411 Spray Tip Screen 5CS43595...
Page 38
18' Folding Boom PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS43644 Center Boom Tube 72” 5CS43646 Side Boom Tube 60” 5CS43616 Boom Hinge Backing Plate 5CS43862 Boom Hinge Bracket 5CS43658 Nozzle Body Single Hose 1/2” 5CS43595 Nozzle Body Dual Hose 1/2” 5CS43843 Air Induction Spray Tip 0.4 gpm 5CS43598 Square Tube Clamp 1”...
Page 39
18' Folding Boom PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS43403 Spring 3/4” x 3-3/4” x .105 03H1506 5/16” x 3” Carriage Bolt 03H2209 5/16” x 1-3/4” Carriage Bolt A22698 5/16” Flange Nut 5CS65090 5/16” x 1-3/4” Hex Bolt 5CS43401 Plastic End Cap 1”...
Page 40
5CS0014 / 5CS0015 - 24' Boomless Nozzle Boomless 24' Spray 6-25-20 Revised: PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS61020 Boom Tube 31” 5CS43597 Tee 1/2” Barb - 1/2” NPT F 5CS43598 Square Tube Clamp 1” 5CS43658 Nozzle Body Single Hose 1/2” 5CS43595 Nozzle Body Dual Hose 1/2”...
Page 41
Boomless 24' Spray PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS43410 Flood Spray Tip 0.3 gpm 5CS43600 Boomless Flat Spray Tip Right 5CS43601 Boomless Flat Spray Tip Left 5CS43411 Spray Tip Screen 5CS43401 Plastic End Cap 1” 5CS43736 In-line Valve 1/2” CTL 3.25”, MF 1/2”...
Page 42
100 ft Hose Reel PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS43686 Hose Reel Base 5CS43687 Hose Reel Assembly 5CS43663 Hose Holder 1/2” 5CS62008 1/4” Bent Pin 5CS43782 Swivel 1/2” FPT, Elbow 5CS50245 Retention Strap Clamp 5CS43783 Swivel Knob A110615 5/8”...
Page 43
100 ft Hose Reel PART ITEM NO. DESCRIPTION QTY. Note NUMBER 5CS65163 7/16” Center Lock Nut 03H1705 7/16” x 3” Carriage Bolt 14H849 7/16” Hex Nut 5CS43781 1/4” x 4” J-Bolt 5CS43725 Spacer 5CS43810 1/4” Plastic Knob 5CS65154 1/4” Washer 03H1540 5/16”...
BOLT TORQUE CHART • Torque values listed are for general use only, based on the strength of the bolt or screw. DO NOT use these values if a different torque value or tightening procedures is given for a specific application. For plastic insert or crimped steel type lock nuts, for stainless steel, or for nuts on u-bolts, see the tightening instructions for the specific application.
Page 45
THIS PAGE INTENTIONALLY LEFT BLANK 5CS2006OM (rev 00 07/2020)
Page 46
THIS PAGE INTENTIONALLY LEFT BLANK 5CS2006OM (rev 00 07/2020)
Page 47
THIS PAGE INTENTIONALLY LEFT BLANK 5CS2006OM (rev 00 07/2020)
Need help?
Do you have a question about the LS2006 and is the answer not in the manual?
Questions and answers