AER Compact 80 pro Manual page 17

6. Technical specifications
Tone controls (each channel)
color Switchable filter
at 700 Hz
at 8 kHz
Only for ch. 1 and 3:
Bass (100 Hz)
Middle (800 Hz)
Treble (10 kHz)
Only for ch. 2 and 4:
Bass (100 Hz)
Treble (10 kHz)
Effects
Internal efx Two independent digital effects for
ch. 1-2 and ch. 3-4.
Presets for each unit:
1. reverb
2. reverb with longer predelay
3. delay, repetitive (320 ms)
4. chorus
External efx
Parallel effect loop, see fx send and fx return
effects pan Blends effect between ch. 1 and 2, or ch. 3 and 4
respectively. The direction of rotation is reverse
for the external effect.
Power amp
Construction Two monolithic ICs with DMOS output in
parallel mode
Rating Output power (THD = 1%)
Continuous output power is determined by the
limiter threshold, see below.
General
Distortion THD + N (8 W / 4 Ω)
Measured at loudspeaker terminals
Noise Residual noise (A-weighted, master in zero
position), referred to rated output power: –99 dB
Acoustical (SPL):
See input specs for noise of specific inputs.
Signal processing
Subsonic filter, adaptive peak limiter
Limiter
Threshold:
Speaker system
8" (200 mm) dual cone full-range speaker,
bass reflex enclosure
Power supply
Mains voltage (depending on model, refer to
type label):
Power consumption:
Mains fuse Size:
Rating (refer to type label)
for 230, 240 V models:
for 100, 120 V models:
Operating temperature
Permissible ambient temperature
Cooling fan Temperature controlled
Cabinet
Material:
Thickness:
Finish: waterbased acrylic, black spatter finish
80 W / 4 Ω
approx. 13 dB (A) / 1 m
65 W / 4 Ω
100, 120, 230, or 240 V~, 50–60 Hz
max. 140 W
5 x 20 mm
T 1.6A L 250V
T 3.15 A L 250V
0...35 °C
Birch plywood
12 mm (0.39")
Dimensions and weight
–3 dB
+10 dB
±8 dB
±6 dB
Notes
±8 dB
Options Configurable by internal jumpers (refer modification to
qualified personnel):
±8 dB
• Deactivation of 48 V phantom power for ch. 2 and ch. 4,
±11 dB
mic input
Definitions
Rated conditions
• nominal input voltage at input under test
• master fully clockwise
• bass / middle / treble / pan centered
• effects level fully anticlockwise
• gain of unused inputs fully anticlockwise
• gain of input under test adjusted to nominal output voltage
at line out.
Nominal input voltage:
Condition for specifications, if not stated otherwise.
Minimum input voltage
Input voltage required for nominal output ratings with
maximum gain and volume settings.
Maximum input voltage
Input voltage that does not cause distortion more than rated
< 0.1%
THD+N, suitable control settings provided.
Nominal output voltage or power
refer to rated conditions.
THD + N
Total harmonic distortion + noise, with input voltage reduced by
10 dB after setting up rated conditions.
Signal / noise ratio
Ratio of nominal output voltage to output noise voltage. Source
voltage reduced to zero after setting up rated conditions.
Equivalent input noise voltage
Noise voltage at output terminals divided by gain of amplifier.
Source voltage reduced to zero after setting up rated conditions.
Residual noise
Output noise with minimal gain and volume settings.
Adaptive limiter
Maintains constant headroom regardless of power supply
fluctuations.
General
Signal voltages are RMS values. Test signal sine 1 kHz sine unless
stated otherwise. Noise measured from 20 Hz to 20 kHz. Noise
stated for a specific input implies that all other inputs are not
used. Sound pressure level (SPL) based on specification by
loudspeaker manufacturer.
Specifications and appearance subject to change without notice.
TD20210421_en (Compact 80 pro)
Height:
Width:
Depth:
Weight (without cover):
320 mm (12.6")
325 mm (12.8")
285 mm (11.22")
10 kg (22 lbs)
17