Related Manuals for Albalá Ingenieros, S.A. AAD2000C03
Summary of Contents for Albalá Ingenieros, S.A. AAD2000C03
- Page 1 AAD2000C03 1 INPUT TO 3 OUTPUTS ANALOG AUDIO DISTRIBUTOR WITH XLR CONNECTORS Version 1.0 Albalá Ingenieros, S.A. 10 October 2016 - © Albalá Ingenieros S.A. - All rights reserved Medea, 4 - 28037 Madrid - Spain...
- Page 2 AAD2000C03...
-
Page 3: Table Of Contents
4.1. Front panel description ......................15 4.1.1. Functions of the INPUT LEVEL LED ................16 4.2. Module remote control and supervision ................17 4.2.1. Details of the AAD2000C03 registers ................18 5. GLOSSARY ........................19 6. REGULATIONS ........................21 7. VERSIONS ......................... 23... - Page 4 AAD2000C03...
-
Page 5: Description
SNMP management and the ability to record events in a file including date and time information for further analysis. The AAD2000C03 is a TL2000 terminal line module and can be housed in a two rack unit (2 RU) UR2000 mounting frame. -
Page 6: Features
Albalá Ingenieros | Manual AAD2000C03 1.2. Features • Analog audio signal distributor. • Excellent intermodulation and wide dynamic range. • Distributes one audio input to three outputs. • Input is electronically balanced. • Low impedance outputs can drive loads of up to 600 Ω at maximum signal levels. -
Page 7: Block Diagram
Albalá Ingenieros | Manual AAD2000C03 1.3. Block diagram... - Page 8 Albalá Ingenieros | Manual AAD2000C03 AAD2000C03...
-
Page 9: Specifications
Albalá Ingenieros | Manual AAD2000C03 2. SPECIFICATIONS Analog audio signal input Connector Impedance >20 kΩ Type Active balanced Common mode rejection ratio (CMRR): at 50 Hz >65 dB at 20 kHz >65 dB Maximum common mode range ±12 V Maximum input level... - Page 10 Albalá Ingenieros | Manual AAD2000C03 AAD2000C03...
-
Page 11: Installation
• The AAD2000C03 module and the mounting frame should always be installed, maintained, operated and removed by personnel with sufficient technical qualifications. The equipment should never be placed in damp areas, near splashing liquid, or in explosive or corrosive atmospheres. -
Page 12: Environmental Considerations
1 - Remove the blank panel covering the front of the empty slot chosen for installing the AAD2000C03 in the mounting frame. 2 - Insert the AAD2000C03 module into the front of the mounting frame. The edges of the card slide into two plastic guides inside the mounting frame. -
Page 13: Analog Audio Connections
Albalá Ingenieros | Manual AAD2000C03 The AAD2000C03 module includes one analog audio input (IN) and three analog audio outputs (OUT1 to OUT3). The front panel has not been designed to support mechanical stress. All cabling in the rack where the mounting frame is located should be properly supported so that the front panel does not provide mechanical support. - Page 14 Albalá Ingenieros | Manual AAD2000C03 AAD2000C03...
-
Page 15: Operation
Albalá Ingenieros | Manual AAD2000C03 4. OPERATION This section describes the significance of the front panel indicators of the AAD2000C03 module and their remote control and monitoring ability. 4.1. Front panel description The appearance of the front panel and the elements it contains are shown in the following illustration. -
Page 16: Functions Of The Input Level Led
The LED shines green when the signal level is above the silence threshold but has not exceeded the overload threshold. The AAD2000C03 uses the peak level meter to update the status LED. The silence threshold and overload threshold are adjustable between -10 and +25 dBu. -
Page 17: Module Remote Control And Supervision
Albalá Ingenieros | Manual AAD2000C03 4.2. Module remote control and supervision The AAD2000C03 can optionally be remotely controlled/supervised. In order to perform remote configuration and supervision of the module an optional TL2000 family remote communications controller must be installed in the mounting frame. -
Page 18: Details Of The Aad2000C03 Registers
- View and adjust the status of the silence and overload detectors. 4.2.1. Details of the AAD2000C03 registers The AAD2000C03 module provides control and status registers that can be read and written by means of specific commands described in the communication control module user manuals. -
Page 19: Glossary
Albalá Ingenieros | Manual AAD2000C03 5. GLOSSARY This acronym refers to the class of connectors described in IEC 61076-2-103. These connectors are commonly employed in professional installations where cabling carries balanced audio in both analog and digital format. The pinout is defined by IEC 60268-12, and is most commonly set as: Pin 1 = shield, Pin 2 = signal with positive phase (+), Pin 3 = signal with reverse phase (-). - Page 20 Albalá Ingenieros | Manual AAD2000C03 AAD2000C03...
-
Page 21: Regulations
Albalá Ingenieros | Manual AAD2000C03 6. REGULATIONS... - Page 22 Albalá Ingenieros | Manual AAD2000C03 AAD2000C03...
-
Page 23: Versions
Albalá Ingenieros | Manual AAD2000C03 7. VERSIONS Ver. Date Description 04-10-2016 Preliminary Version 10-10-2016 First version... - Page 24 Albalá Ingenieros, S.A. Medea, 4 - 28037 Madrid Spain +34 913274453 www.albalaing.com info@albalaing.com...
Need help?
Do you have a question about the AAD2000C03 and is the answer not in the manual?
Questions and answers