KP Electronic Systems SIM900 Installation Manual

MATC™
Mini Alarm Transmitter
Cellular
Installation Manual
Web Site: www.kpsystems.com
ISRAEL Office
Email: info@kpsystems.com
Tefen Industrial Park, Tefen 24959
Tel: 972-4-987-3066 Fax: 972-4-987-3692
USA Office:
KP ELECTRONICS INC.
Email: info@kpsystems.com
415 Sargon Way Suite F Horsham PA 19044
Tel: (215) 442-7460 Fax: (215) 442-7461
P.N.: Book 135
Rev New 20/10/2014
This Document refers to MATC™ hardware
MATC™ General Description
MATC™ is a compact long-range, cellular alarm
transmitter. The MATC supports all four GPRS
frequencies: 900/1800 or 850/1900 MHz.
The MATC™ operates in two modes, SMS and
TCP/IP.
When the MATC™ detects an alarm condition at
one, or more of its inputs; an encoded digital alarm
message is prepared. It is then transmitted to the
alarm center, according to the selected mode.
The MATC™ has three sets of connectors: J1, J2,
and the SMA ANT (see Figure 1).
1. J1: A 9-pin contact connector for the
following connections (see Figure 1):
 12 VDC battery (contacts 1 and 2)
 Common Ground (contact 3)
 4 inputs for sensors
(contacts 4 - 7)
 Two serial communication
connections: SI and SO.
Table 1: LEDs description
Purpose No. of Description
blinks/Color
Fast Blinking Modem is not registered
Net Led
[Led 4-Red]
Slow Blinking The modem is registered
Will blink each time a
1 transmission is made in
Transmission
SMS Mode
Led
Will start blinking rapidly
[Led3-Red]
Fast Blinking at the beginning of a data
transmission (TCP mode)
Power on reset and all
1
OK/Received SMS
2 SMS was not sent
3 Communication problem
4 Modem Reset
5 GPRS Detach
Low battery
Status Indication
6
(bellow 9[V])
Led
Failed to register to the
[Led2-Green]
8
network
No SIM card or PIN code is
Fast Blinking
enabled
The MATC is ready to
receive an event from the
Constant-on panel or from the direct
inputs.
No reception
Off
[-113dbm]
Poor reception
Red
RSSI Led
[-111dbm]
[Led1-BiColor]
Good reception
Green
[-109-(-51dbm)]
J2: The 6-pin programming connector
Communication parameters are easily
programmed using GUP5000™ utility-
programming software. (See book 123).
An external antenna can be connected
ANT:
using the SMA connector.
Figure 1: MATC™ External View
Preparing for Operation
Before installing the MATC™ on site,
perform the following preparations:
 Setting communication parameters
 Preparing inputs
 Connecting antenna, sensors and battery
Setting Communication Parameters
See book 123.
Preparing Inputs
The 4 MATC™ inputs are factory set. By
default they are set as NC (Normally Closed).
Connecting Alarm Panels
Prepare a panel according to manufacturer
rules. There are three ways to connect the
MATC™ with an alarm panel:
 Caddx NX4, NX6, NX8 can be directly
connected to the serial port J2, using the
INT004™ cable.
For Caddx, connect all three INT004
wires to the alarm panel – lines Red to
"Pos" Black to "Com" Green to "Data".
Connect the cable to J2. (Connect the
INT004™ before connecting the
battery).
 Any other alarm panel can be connected
via the DI100™, enabling it to transfer
full Contact ID data.
 Connect the alarm panel's PGM to the
MATC™ inputs.
Connecting Antenna, Sensors and Battery
1. Connect the antenna to the SMA connector.
2. Connect sensors to J1 (contacts 4–7).
3. Connect the battery to J1: red wire (+) to
contact 1, black wire (-) to contact 2.