Advertisement
Interface Description/ 接口说明
NOTE/ 说明
• The pigtail of the C6620-Z23-Sf camera does not contain the number 4 (audio cable) or number 5 (alarm cable).
C6620-Z23-Sf款型摄像机的尾线不含编码4（音频线）和编号5（告警线）。
Type
NO.
Item
Description
型号
序号
名称
说明
Power input interface. 24 V AC (-25% to +24.9%).
1
POWER
电源输入接口。支持AC24V(-25%~24.9%)电源输入。
C6620-Z23
C6620-Z33
C6650-Z33
100M adaptive network port, supporting PoE+ power supply.
2
LAN
100M自适应网络接口。同时还支持POE+供电。
C6620-Z23-Sf
Ground interface of an IPC.
3
GND
设备接地接口。
AUDIO IN/
Audio input/output interface and audio ground interface.
4
AUDIO OUT/
AUDIO IN/AUDIO OUT为音频输入/输出接口。AUDIO_GND为音频接地接口。
AUDIO_GND
Alarm output interface. A pair of ALARM_OUT and ALARM_REF forms a
single alarm out.
The rated power of the device driven by alarm output is less than or equal
ALARMOUT/
to 30 W, and its rated voltage is less than or equal to 110 V DC or 125 V AC.
ALARM_REF
告警输出接口。ALARM_OUT和ALARM_REF组成告警输出。
C6620-Z23
告警输出所驱动设备的额定功率不大于30W，额定电压不高于DC 110V或AC
C6620-Z33
125V。
C6650-Z33
5
Alarm input ground interface.
ALARM_GND
告警输入接地接口。
Alarm input interface. There may be multiple alarm interfaces. For a given
number of interfaces, n, they are numbered (for example: ALARM_IN0,
ALARM_IN1, ..., ALARM_INn). Each one connects to the GND connection to
ALARM_INn
form a single alarm input.
告警输入接口，n为0～1之间的整数。ALARM_INn和ALARM_GND组成一路告警
输入，一共2路。
Reset Button and SD Card Slot/Reset 键和 SD 卡槽
1
2
3
4
4
NO.
Description
序号
说明
Reset button. To restart the device, hold down the reset button (less than 3s). To
5
restore the device to factory settings, hold down the reset button for at least 5s
while the device is running.
Restoring the factory configuration will result in the loss of the user's account
1
information and some of the configuration information. Please exercise caution
when performing this operation.
重置按钮。运行时按住Reset键短于3秒重启设备，运行时按住RESET键不短于5秒后恢复出厂配
置。 恢复出厂配置将会导致用户的账号信息以及部分配置信息丢失，请慎重操作。
SD card slot. The SD card slot supports only class 10 or higher Micro SD cards.
To replace a Micro SD card, the device must be powered off. Otherwise, system
exception may occur. When a Micro SD card is used for the first time, log in to
2
the web client of the device and format the Micro SD card. For details, see the
Configuration Guide.
SD卡卡槽，支持Micro SD卡（Class 10及以上）。请在设备断电的情况下插拔SD卡，否则会造成
系统异常。首次使用时，请登录设备Web客户端，格式化SD卡，操作方法请参见《配置指南》。
Prepare for Installation Tools/ 准备安装工具
Wiring terminals
接线端子
Marker
记号笔
M8 socket wrench
套筒扳手（M8）
#2 Phillips screwdriver
十字螺丝刀（2#）
2
Reset
1
2
Reset键位于SD卡槽侧边,
reset键按压方向与SD卡插拔方向垂直。
The Reset button is located at the side of
the SD card slot. The direction for pressing
the Reset button is vertical to that for
inserting and removing the SD card.
Diagonal cutting pliers
斜口钳
10 mm hammer drill
(for pendant- or wall-mounted installation)
(for ceiling-or wall-mounted installation)
冲击钻,Φ10mm（吊顶和墙壁安装时使用）
Wire stripper
剥线钳
Glass cement
玻璃胶
Operation
操作
Use a Phillips screwdriver
to remove the camera
bottom cover. Then, you
can see the Reset button
and SD card slot.
使用十字螺丝刀将球机后
盖卸下，即可看到重置键
和SD卡槽。
Measuring tape
钢卷尺
Hammer
羊角锤（吊顶和墙壁安装时使用）
RJ-45 connector crimping tool
水晶头压线钳
H3 hex key
内六角扳手（H3）
Advertisement
