Toro MB-1600 Operator's Manual page 5

– Keep container nozzle in contact with the tank during
filling.
•
Ensure that the machine's shields are attached and
functioning properly. Do not operate unless they are
functioning properly.
Operation
WARNING
The maximum payload is reduced to 850 kg (1875
lb) when operating the machine without the dual
wheels.
•
Never run an engine in an enclosed area.
•
Only operate in good light, keeping away from holes and
hidden hazards.
•
Be sure all drives are in neutral and parking brake is
engaged before starting the engine. Only start the engine
from the operator's position.
•
Slow down and use caution when making turns and when
changing directions on slopes.
•
Watch for holes, ruts, or bumps, as uneven terrain could
overturn the machine. Tall grass can hide obstacles.
•
Stop and inspect the machine if you strike an object.
Make any necessary repairs before starting.
•
Never operate with the guards not securely in place.
•
Do not change the engine governor setting or overspeed
the engine.
•
Stop on level ground, engage the parking brake, shut off
the engine.
•
Keep hands and feet away from moving attachments.
•
Look behind and down before backing up to be sure of
a clear path.
•
Never carry passengers and keep pets and bystanders
away.
•
Slow down and use caution on uneven terrain, and when
making turns and crossing roads and sidewalks.
•
Do not operate the machine under the influence of
alcohol or drugs.
•
Use care when loading or unloading the machine into a
trailer or truck.
•
Use care when approaching blind corners, shrubs, trees,
or other objects that may obscure vision.
•
Never leave a running machine unattended. Always stop
the engine and set the parking brake.
•
Do not exceed the rated operating capacity, as the
machine may become unstable which may result in loss of
control; refer to Specifications (page 10).
Do not over-load the hopper and always keep the load
level when operating.
•
Never jerk the controls; use a steady motion.
•
Watch for traffic when operating near or crossing
roadways.
•
Do not touch parts which may be hot from operation.
Allow them to cool before attempting to maintain, adjust,
or service.
•
Check for overhead clearances (i.e. branches, doorways,
electrical wires) before driving under any objects and do
not contact them.
•
Only operate the unit in areas where there is sufficient
clearance for the operator to safely maneuver the product.
•
Locate the pinch point areas on the machine and keep
hands and feet away from these areas.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
Slope Operation
Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or death.
All slopes require extra caution.
•
Do not operate the machine on hillsides or slopes
exceeding the recommended angles.
Operate up and down slopes with the heavy end
of the machine uphill. Weight distribution changes.
An empty hopper will make the rear of the machine the
heavy end, and a full hopper will make the front of the
machine the heavy end.
•
Slow down and use extra care on hillsides. Be sure to
travel in the recommended direction on hillsides. Turf
conditions can affect the machine's stability.
•
Keep all movements on slopes slow and gradual. Do not
make sudden changes in speed or direction.
•
Avoid starting or stopping on a slope. If the machine
loses traction, proceed slowly, straight down the slope.
•
Avoid turning on slopes. If you must turn, turn slowly
and keep the heavy end of the machine uphill.
•
Do not operate near drop-offs, ditches, or embankments.
The machine could suddenly turn over if a wheel goes
over the edge of a cliff or ditch, or if an edge caves in.
•
Use care when operating on wet surfaces.
•
Watch for material coming out of the hopper. Materials
dumped from this machine can be hazardous to people
and objects.
•
Do not park the machine on a hillside or slope without
setting the parking brake and blocking the wheels, if
required.
4